• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Search results

  1. wesleydax

    Caddy caliper e-brake holding power

    I had been thinking of a band brake. had one on an old international rollback that worked well. If i find something that will work ill post back
  2. wesleydax

    Caddy caliper e-brake holding power

    where did you install the line lock control? Is it just a push pull knob or electrically activated. I like the line lock idea over swapping to explorer disc set up.
  3. wesleydax

    Caddy caliper e-brake holding power

    Thanks for the info. Mine is also hydro. Line lock may be the way i go. Only need it for a few min. each time and would rely on it in emergency anyway.
  4. wesleydax

    Caddy caliper e-brake holding power

    Hi all. I have started using the bronco a lot to pull the boat. I already have disc all way around and they work great. I want to add e-brake capability. I have chevy calipers on the back now and thinking about swapping to the caddy e brake calipers. for those using this type caliper how well...
  5. wesleydax

    Electric Fuel Pump/ Inertia Switch

    put mine on the kick panel under the dash.
  6. wesleydax

    Want to buy durable headers (non rusting)

    stainless or titanium would be the way to go. If you do go with coated steel get black. the polished ceramic coating is water base and the black or cast is solvent base, it tends to hold up better.
  7. wesleydax

    P0300 cold start stumble

    after several trips today the issue has not repeated it self. yes i did try cycling the key to make sure pressure was good. when i did that it still stumbled. If it happens again ill hook laptop up and see if efi guy can look at it.
  8. wesleydax

    Ceramic Header question

    You may be better off getting raw steel and take them to a local coater. the'll be done right and last longer. We have coated stainless though not as much. I guess it depends on the type of stainless.
  9. wesleydax

    P0300 cold start stumble

    where would i check for the ac volts? at the charge post?
  10. wesleydax

    P0300 cold start stumble

    I dont think i mentioned this, but the reason i thought voltage was the other day when starting or just after the gps gave a low battery notice.
  11. wesleydax

    P0300 cold start stumble

    Shut it off and crank right back no issues. Normally sitting for over an hour will cause it but not always. This morning drove it to church sat for about a hour and a half cranked right back no issues. It will always crank and run just rough sometimes. I dont have a fuel pressure gauge but i...
  12. wesleydax

    Ceramic Header question

    properly coated and cared for ceramic should last a long time. We redo several sets from some of the larger coaters. The main reason we see coating failure is improper or lack of proper prep. The ceramic is a baked on coating that is baked on, and it is no different than wet paint the surface...
  13. wesleydax

    P0300 cold start stumble

    will be doing more checking today. it is at most 13.7 on voltage. would this be enough to maintain the battery over a long period
  14. wesleydax

    P0300 cold start stumble

    Its late. No glasses. O wait. Thats why i wouldve missed it
  15. wesleydax

    P0300 cold start stumble

    Only code is the p0300
  16. wesleydax

    P0300 cold start stumble

    returnless system. It has ran great for a coupe month since swap. It runs great now after the first 10-15 sec of stumbles,(that dont always happen) has plenty of power, idles fine. everything was swapped from the explorer.
  17. wesleydax

    P0300 cold start stumble

    well it will run without the charge wire hooked up. Found that out the hard way, a battery will only last so long till your walking:-[. just went out and checked it and no wire to alt its putting out 2.5v but as soon as the wire is hooked back it goes to 13.74. static battery voltage is 12.4...
  18. wesleydax

    Ceramic Header question

    if there ceramic coated then no they should not rust, and should not chalk. I had a customer bring a set in to be coated for his bronco. They we supposed to be coated already but were just shiny raw metal.
  19. wesleydax

    P0300 cold start stumble

    so if this is sinking in right. if i unhook the charge wire from the alt. and attach my test meter to the terminal i should get charge voltage on start up? I did load test the battery at the post and with a load it dropped to 10.5. would that be an issue.
  20. wesleydax

    P0300 cold start stumble

    Thank you. I will take it off tomorrow and get it checked out monday
Top