• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

200 straight 6 ticking!

Scott C.

Sr. Member
Joined
Oct 10, 2009
Messages
667
Loc.
Waynetown IN
It sounds like you are adjusting them properly. Have you tried adjusting them with out the engine running? TDC compression stroke of each cylinder, zero lash ans then 1/2 to 1 full turn. It should not make any differance dead or running.

What is your timing set at? Is the vacume and mechanical advances both working properly?

Do you ever get the noise to go away at all?

Are the rockers new too with that new shaft?

Can you wiggle any of the valves by hand?

Are you locking the rocker screws in place with the jam nuts? If, it has them?

Have you checked averything we have mentioned?
 
OP
OP
B

Betsybronco

New Member
Joined
May 30, 2013
Messages
27
Yes I have done everything you guys suggested. I did it when not running and same thing there are no lock down nuts the tapers are just tight in the threads that what holds them. The rocker assembly came as one ore assembled and they are tight as in good fit meaning rockers to. The valve guides are new. It really sounds like a loose lifter
 
OP
OP
B

Betsybronco

New Member
Joined
May 30, 2013
Messages
27
I checked the rockers and one of them isn't hitting in the center but off to the side will this do it?
 

Scott C.

Sr. Member
Joined
Oct 10, 2009
Messages
667
Loc.
Waynetown IN
Why is it off to the side? Is it the rocker? Or, the valve? If the sound never goes away, have you narrowed it down to one particular valve?

Where are you located?
 
OP
OP
B

Betsybronco

New Member
Joined
May 30, 2013
Messages
27
I have narrowed it down to two valves I'm pretty sure. I live in boring Oregon. The valves are tight and new. I don't know if the machining of the rocker arms were wrong? It has ticked since we rebuilt it
 

72_EB

Contributor
66to77
Joined
Feb 4, 2003
Messages
4,982
Make sure your new valve train hasn't caused the rocker studs to start pulling out. Seen that before.
 

Scott C.

Sr. Member
Joined
Oct 10, 2009
Messages
667
Loc.
Waynetown IN
I think the rocker arms are all the same on those? So, it should not matter about the location of each one. Are all of the springs and or shims in place on the rocker shaft? Take the shaft off and check to see if any of the rockers are loose on the shaft. Maybe even move the rockers from the trouble spots to another, just to eliminate things.

Are all of the rocker stands the same? Or, are there 2 different ones? If so, are they in the right places?

Can you email me some pictures of the shaft assembly on the head?
scottandnona@att.net
 
OP
OP
B

Betsybronco

New Member
Joined
May 30, 2013
Messages
27
The stands are all of the same except the very first one, its the one that oil dumps out of. There are no shims just the springs that push to keep them on the one side.
 

72_EB

Contributor
66to77
Joined
Feb 4, 2003
Messages
4,982
You're correct. I'm sorry. Typing before the coffee kicked in this morning. %) I was thinking a 289 or V8 stud setup. You do have bolts with the long rocker arm shaft. Was that replaced by the way? Springs were changed with the new cam? New pushrods as well? Rocker arms are original?

There are bolts that go into the head not studs And they are torqued
 
OP
OP
B

Betsybronco

New Member
Joined
May 30, 2013
Messages
27
100% everything brand new. I took the springs off today and the top washer that the keeper sit in cut in to the valve springs the engine only has 3000 miles on it and I took two valves apart and they are the same. Are the springs wrong? I would post some pictures but I don't know how haha
 
OP
OP
B

Betsybronco

New Member
Joined
May 30, 2013
Messages
27
The springs could be wrong I had dons machine shop assemble the short block and the head and after I put the pan on I rolled the engine over and I heard a clank so I pulled it back off and they had left and old lock washer on one of the rods and it fell in the pan
 
OP
OP
B

Betsybronco

New Member
Joined
May 30, 2013
Messages
27
By the way I would have assembled the whole thing I just have never had good luck with rope seals!!! Haha
 

Scott C.

Sr. Member
Joined
Oct 10, 2009
Messages
667
Loc.
Waynetown IN
You should be able to buy the rockers individually. At least you could back in the day.

So, you are saying that the valve spring does not fit the valve spring retainer? Why would that be on only 2 valves?

Do you think the noise is actually the valve spring moving around against the retainer?
 
OP
OP
B

Betsybronco

New Member
Joined
May 30, 2013
Messages
27
I'm thinking its the springs. I only took two off that's why I only saw the two. The retainer wore a pretty deep grove in the top of the spring. The springs arnt center on the retainers they are slightly off to the side is that the problem?
 

Scott C.

Sr. Member
Joined
Oct 10, 2009
Messages
667
Loc.
Waynetown IN
It very well could be the source of the problem. With them having been pushing to one side like that, I would pull the head and check all the valves and and valve guides again for wear. That much of a side load could have worn them too, just like the springs. Are the retainers still OK? Or, did the springs samage them too?
 
OP
OP
B

Betsybronco

New Member
Joined
May 30, 2013
Messages
27
The retainers look fine just the springs I wish I could show you guys!! The valve guides are tight I checked them
 
Top