• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Ax15/NV3550

BucksNBroncs

Full Member
Joined
Jul 29, 2016
Messages
152
Loc.
Klamath Falls
I may have found a good deal on an AX15 or NV3550 tranny? Came off Jeep Wrangler 4.0 but guy doesn't know what year. Number on the tranny is 52108949. I know the bolt patterns are the same and the AX housing is all aluminum. So far the only picture I have doesn't show the bolt pattern anyway.

Any other advice on how I can positively identify which it is? Also, anything helpful to determine its condition ?

I have no clue what to look for but I'm certain I want to do a 5 speed conversion with either of the two options. Seller is asking $200

Any advice would be appreciated!
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Here's a link that may help you. https://www.novak-adapt.com/
both trannys are all aluminum and I believe the adapter kits fit both so it may not matter which one it is. either way $200 is a good deal if its either tranny in good shape. It may be a AX15 as the I didn't see the PN given under a list for the NV3550. but it was close so who knows theres always part numbers that are not on lists that people compile.
 
Last edited:

01JLH

Sr. Member
Joined
Sep 3, 2007
Messages
392
The adapters for the rear of both trans do interchange. Adapter, Spud shaft adapter, crossmember, trans mount and reverse light pigtail everything on that end.
On the bellhousing end, the adapter to bolt to the bellhousing is different. The Nv3550 requires a small modification to the ford bellhousing and the Ax-15 does not. There is a shift tube that extends past the front of the shift tower on the 3550 so you have to enlarge the vent hole in the bellhousing so that shift tube can fit inside of the enlarged vent hole.
The clutch disc, pressure plate and pilot shaft bushing interchange between the two.
Both are really nice for the bronco conversion. The shifter comes out in the perfect place and looks like a factory job if you convert the steering column over with a smooth shifting collar.
 
OP
OP
B

BucksNBroncs

Full Member
Joined
Jul 29, 2016
Messages
152
Loc.
Klamath Falls
Thanks for the input so far. Heard back from the seller. He is pretty sure that its from a late 90's Wrangler. Were any of those 2WD? And if so, is there a telltale sign to determine when looking ?
 

01JLH

Sr. Member
Joined
Sep 3, 2007
Messages
392
Share a picture of the rear end of the trans and we can tell you if it is a 4wd version. If its not, pass on it. Rear of 4wd version will will be a 8 to 10 inch 6 bolt roundish or hexish flange that the tcase bolts to.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
On the bellhousing end, the adapter to bolt to the bellhousing is different. The Nv3550 requires a small modification to the ford bellhousing and the Ax-15 does not. There is a shift tube that extends past the front of the shift tower on the 3550 so you have to enlarge the vent hole in the bellhousing so that shift tube can fit inside of the enlarged vent hole.
The clutch disc, pressure plate and pilot shaft bushing interchange between the two.

I have a minor hijack... Can a bell housing adapter made for the NV3550 transmission be used for the AX-15 transmission, but not the reverse?
The reason for my question is, I have the Advance Adapters NV3550 setup. There has been the concern that the NV3550 may become obsolete due to lack of support. I like my NV3550, but if I need to, can I just use my existing adapters on a AX-15?
 

01JLH

Sr. Member
Joined
Sep 3, 2007
Messages
392
I can answer that for you. In short, just like i said, no they cannot be interchanged unless you melt down the aluminum and start over. Completely different. I've been there done that and had to just buy the AX15 bellhousing adapter. It's not extremely expensive anyway it comes with the snout that is required for your throwout bearing. The bolt pattern on the front of the bare trans is different and the way the snout is handled is different.
Wish i had a more favorable answer for you, but i did this myself.
 

Pops68

Contributor
Bronco Rookie
Joined
Oct 11, 2010
Messages
1,777
Loc.
Bazetta Township
You may want to get the mileage on it. I paid over $800 for a 4X4 NV3550 out of an '04 (I think) Wrangler a few years ago that had around 24,000 miles on it. At $200, may be high mileage and in need of rebuild/repair. Mine also came from the SW US - dry climate is a plus.

Pops
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Another hi-jack...
Does anyone know what Jeep's recommended oil change interval is on both the NV3550 and AX-15?

Never mind, I found it...

Frequency of Fluid Change
Under normal operating conditions, the fluid installed at
the factory will give satisfactory lubrication for the life of
the vehicle. Fluid changes are not necessary unless the
lubricant has become contaminated with water. If contaminated
with water, the fluid should be changed immediately.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Interesting. Good to know that.
I'll probably end up changing mine at some point anyway, but apparently their confidence is pretty high regarding that fancy synthetic stuff they recommend.

Paul
 
OP
OP
B

BucksNBroncs

Full Member
Joined
Jul 29, 2016
Messages
152
Loc.
Klamath Falls
this one has 14 spline input and 21 spline output and 15.75" case measurement. No go right.?? Not an AX15???
I have some pics I could post later this evening but if the above info answers my question, I won't bother....
Thanks in advance
 
Top