• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Best Bilstein Valving

Dandesjar

Jr. Member
Joined
Aug 20, 2016
Messages
86
Just looking for opinions on the correct valving for the best riding setup for street use with Bilstein 5100 shocks? Leafs & coils are a Deaver 2.5" lift, with original shock mount locations.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
What does your Bronco weigh, what size tires you running, and how do you want it to drive? Will you use stock or aftermarket shock mounts?
I know you gave the basics already, but a little more detail please.

Reason is that the "best" valving for most with plain-Jane EB's might not be just right for someone with a heavy winch and bumper hanging off the front, or a big double-rack tire carrier kitchen-on-wheels bumper out back.
Doesn't sound like that's how yours will be set up, but just making sure.

The valving (in the 5100's) that has been working out so well for us has been the 298/94 in the front using stock mounts, and 255/70 in the rear with stock mounts.
It's very comfy on the road but with good control in a soft to medium sprung Bronco that's fairly light. Probably a bit soft for heavier rigs or those driven hard however.

Hope that helps.
Fill in some more details if you want and maybe some of the others that have played around with the valving or used multiple shocks (very few I would think) will have some other recommendations.

Paul
 
OP
OP
D

Dandesjar

Jr. Member
Joined
Aug 20, 2016
Messages
86
Thanks Paul. Not sure exactly what it weighs but I would say it's on the lighter side ... stock bumpers, no spare tire carrier, no winch, and run it without the hard top most of the time.

I'm running 33" tires on 15" rims and will likely keep that set up for the foreseeable future.

The shock mounts are in the stock location although I'm planning on installing a rear disc kit from Tom's which will move the rear lower shock mounting points inboard by an inch or two (if that matters).

I'm looking for the most comfortable ride on the street as it will be spending 99% of its time on pavement once it's back on the road after my restoration.
 

SteveL

Huge chevy guy
Joined
Jun 24, 2001
Messages
11,969
Loc.
Hawthorne ca
How do you change valving on the 5100s or do you need to order specific valving when you buy em? I have a set that are way too soft.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
You can't change the 5100's. That's only something you can do on the more expensive shocks, such as the 7100's and others like that.
There are only certain levels of valving available on 5100's, and there are other variables as well, such as what "type" of valving a particular part number uses.
Perhaps all 5100's use the same type, but Bilstein uses probably 10 or more proprietary designs to get the performance they're shooting for on a particular vehicle.
In other words, you might be able to find a shock that has the same mounting style and same dimensions, with a valving characteristic you like, but it might have a different design that makes it act differently on a Bronco than it would on a Toyota pickup for example.

But this is why many people opt for 7100's in spite of the roughly triple price they incur.
With those, you even get one free re-valve from the factory if your initial choice is not optimal. You simply send them in and they will re-do it for you.
They'll do it as often as you want of course, but it costs you after the first time.

The other option is duals. Even though that method makes choosing the correct valving for your particular needs even more finicky and head-scratching, it can work very well for someone that needs firmer valving.

Do you know exactly what you have Steve? If so and there is another 5100 that's a step up in firmness with the same mounting and roughly the same dimensions, that might be all that's needed.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Not sure exactly what it weighs but I would say it's on the lighter side ... stock bumpers, no spare tire carrier, no winch, and run it without the hard top most of the time.
I'm running 33" tires on 15" rims and will likely keep that set up for the foreseeable future.

I'm looking for the most comfortable ride on the street as it will be spending 99% of its time on pavement once it's back on the road after my restoration.

Off the top of my head, unless someone else (Steve perhaps?) has a different recommendation, I would have to say that you sound like a perfect candidate for the standard numbers I recommended above.
Don't see anything that would say otherwise.

Even mine with the heavy Hanson bumper and winch is not bad. It's not perfect, but it's still the best combination I've ever run (so far!). It's quite safe and good handling, with a very good ride.
It's really only a tiny bit soft. Enough that I notice, but not enough that I'm ready to go to the next level until I do some other, more important things.
I do have smaller tires than you, but based on how it feels, it's that big weight hanging way out front that is I'm sure what puts it just over the edge.

Let's get some more feedback from Steve and others too before you make a decision. Most people with similar setups to yours are very happy. But it never hurts to get as much input as possible before spending your money.
Measure twice, cut once in other words...;D

Paul
 

SteveL

Huge chevy guy
Joined
Jun 24, 2001
Messages
11,969
Loc.
Hawthorne ca
Thanks. Didn't think they were adjustable. These are on my dd (72 suburbs 4x).the old shocks were shot so I went with 5100s. They're fine in the rear but too soft up front. Thinking about throwing 9000s up front. When I get back on the bronco it's getting 7100s for sure up front but probably on all 4 corners. Sorry for the highjack.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Oh yeah. I can see them being too soft for a Suburban! Even with the wheels pretty far forward in the vehicle, that's a lot of weight overall transferring back and forth when driving around.
In the later years they used dual shock setups from the factory on the front that actually worked very well.
This is one of those instances when a dual setup, even using the same valving, would likely get you what you needed without too much additional harshness. It would be "firmer" of course (which is a good thing!) but likely not too "stiff" on a big rig like yours.

Normally we try to use two lighter-valved units together in a dual setup, but on some vehicles two full-strength valved shocks is the better route.
Of course, the 9000's get rid of all the guesswork and will likely be stiff enough for sure. I just never found a happy place with my 9000's on either the Bronco or the F350 unfortunately.
Not sure I want to try off-the-shelf 5100's on the big truck either. But not going to go back to 9000's either unless I can find some that have just the right valving to start with.

Good luck on all fronts!

Paul
 
OP
OP
D

Dandesjar

Jr. Member
Joined
Aug 20, 2016
Messages
86
Thanks guys, does Wild Horses list a set of 4 shocks with this valving (298/94 & 255/70) online? I see a few sets listed but don't see where it specifies this valving. Do you happen to have a part number?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Actually we do. All of ours should fall within that valving category, but depending on what you are working on there might be variations.

If your ride height is stock to 2" of suspension lift, you would use the BIL88000.
With your 2.5" of suspension lift and stock mounts, the BIL88001 is your set of four.
The individual numbers are listed on this page as well: https://www.wildhorses4x4.com/category/s?keyword=bilstein
(update: the BIL88001 set is indeed the valving specified previously)

I'll check just to make sure. Sometimes I don't always "get the memo" when there is a minor change!%)
Usually when that's the case though, the change was not considered enough to cause any trouble with what a customer expects.
But I like to know anyway, in case the customer needs something specific and expects it.

You know... Nothing to cause trouble until a customer calls and says, "hey, why are my u-bolt plates silver when you told me they were black?" or something like that.;);D

Thanks for checking us out Dandesjar.
Let you know what I find out.

Paul
 
Last edited:

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Updated the last post to include the info that the valving is indeed what we've been talking about.

Paul
 
OP
OP
D

Dandesjar

Jr. Member
Joined
Aug 20, 2016
Messages
86
Thanks Paul, that's exactly the info I was looking for. Now just hoping for a Black Friday sale...
 
Top