• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Best floor pan paint

Johnnyb

Contributor
Bronco Guru
Joined
Nov 19, 2001
Messages
1,233
Loc.
Flagstaff
My drivers and passengers floor pans are slightly rusty, but structurally sound. That is to say, I can't do The Flintstones, or put a screwdriver or a ball peen hammer through them anywhere. They feel strong.

It's only the lowest portion of the pan that even has surface rust, the rest of the floors and bed all have factory paint from '71.

Now I'm looking to reinstall my cage, and I'm wondering about the best surface prep and paint to use once I brushed off the surface patina to bare metal.

Any recommendations appreciated,

-JB
 

Gupster88

Contributor
Guppy
Joined
Jan 15, 2019
Messages
854
Loc.
Tillamook OR
Personally I would line x them . Such a high traffic , scuffed up area. My two cents. You can even have them color the linex
 
Last edited:

gnpenning

Contributor
Bronco Slave
Joined
Dec 26, 2011
Messages
2,601
Loc.
I have more questions than answers.
If you can't get all the rust out a POR type of product. If you can, I would start with proper prep then an epoxy primer.

Not a big fan of bed liner types after having water creep underneath, finding out by major rust. Yes, I followed all the instructions.
 
Last edited:

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
No matter what you use, if it’s a thick coating make sure you take lots of pictures of the metal prior to coating. That way there’s no question that you were trying to hide or cover up something.
Even if it’s not going to be for sale anytime soon, you will at least have the pictures for whatever the future brings.
 

armynavy17

Contributor
Sr. Member
Joined
Jan 9, 2010
Messages
361
Epoxy paints are considered to be the gold standard in wearing well; however, "chalk" up and change color when exposed to UV. Polyurethane paint doesn't chalk up, but does tend to loose it's gloss over time and doesn't wear as well as epoxy.

Either way, proper prep is key for paint adhesion along with recoat intervals and mil thickness per the technical data sheet for your specific product. If you can't get all the way to clean metal everywhere. I recommend Corroseal before the primer.

Unless absolutely impossible, 2 stage paint is a must in my opinion for such a high traffic area. The other option is to rattle can it knowing it won't last but you can hit it again with more spray paint frequently.
 

bronkenn

Contributor
Bronco Guy
Joined
Apr 27, 2017
Messages
2,717
Loc.
Southeast Ohio
POR with the proper prep in really durable and will stop any further rust. You can top coat it with a preferred color if needed.
 

Bronco-Brian

Full Member
Joined
Jun 30, 2015
Messages
306
Loc.
Lake Oswego, OR
POR15, then an epoxy primer, then a polyurethane top coat of your color choice. If you leave a mat or carpet over the primer to prevent UV exposure you should also be OK. If not covering then bed liner over the epoxy is a good solution.
 

fordguy

Contributor
Bronco Guru
Joined
Jan 23, 2005
Messages
6,361
Not a fan of bed liner, mine had it it when I bought it and I pulled it out. It was like removing vinyl flooring in a home. I have used por many times and it works.
 

1buckeyefan1

Sr. Member
Joined
Sep 21, 2017
Messages
641
How about a slight twist to this question? What is everyone using for floor paint below carpet? I sandblasted mine down to bare metal and put epoxy primer over it.. plan to dynomat it.. my painter recommended brushing on a 'cheap' Rustoleum or Blitz Black (TSC Black) oil based paint.. any other ideas?
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
I am a big fan of por 15 wire brush what you can then paint on the por. then cover with what ever you want on top.
 

armynavy17

Contributor
Sr. Member
Joined
Jan 9, 2010
Messages
361
How about a slight twist to this question? What is everyone using for floor paint below carpet? I sandblasted mine down to bare metal and put epoxy primer over it.. plan to dynomat it.. my painter recommended brushing on a 'cheap' Rustoleum or Blitz Black (TSC Black) oil based paint.. any other ideas?
You'd be fine with two coats of a good two part epoxy primer in my opinion.

Coatings are a system. For optimal performance they need to be selected carefully, mostly in regards to compatibility. You're looking for a chemical bond between the layers or a strong physical bond. This is why recoat intervals are so important.

Without knowing the specific epoxy primer you used, there's no telling what the compatibly with the specific oil based top coat you have in mind would be.
 

1buckeyefan1

Sr. Member
Joined
Sep 21, 2017
Messages
641
You'd be fine with two coats of a good two part epoxy primer in my opinion.

Coatings are a system. For optimal performance they need to be selected carefully, mostly in regards to compatibility. You're looking for a chemical bond between the layers or a strong physical bond. This is why recoat intervals are so important.

Without knowing the specific epoxy primer you used, there's no telling what the compatibly with the specific oil based top coat you have in mind would be.

That was my original plan... I used Nason Fulpoxy (before i learned about SPI), then Dynmat, then carpet. But then the analysis paralysis set in and I started thinking about another coat to avoid moisture/rust issues under the dynomat.
 
Top