• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Black Cloud Boob Job Build Thread

OP
OP
C

coby

Full Member
Joined
Apr 24, 2003
Messages
317
Loc.
Fort Collins, CO
I stick with Canon bodies and lenses.

BTW...the camera you use doesn't matter as much as you think....but getting good lighting is pretty damn important. Even with point and shoots there's things you can do to improve your shots, like putting a piece of paper over the pop up flash to reflect the light to the ceiling to reflect down onto the part, or to diffuse it for direct light. Head over to Strobist.com for a ton of low cost tips on how to shoot great shots.
 
OP
OP
C

coby

Full Member
Joined
Apr 24, 2003
Messages
317
Loc.
Fort Collins, CO
Here's a shot of the 40" e series light, showing the focusing. This is half the light....the ones on the right are the wide pattern (diffuse); the ones on the left are the focused spot pattern. The light features a wide and a spot pattern at the same time; the outer 10" on either side is the wide beam and the inner 20" is the narrow beam.

20120218-IMG4136-X2.jpg


Here's a bunch more shots of both the 40" light and the Dually D2's, including showing the pretty cool mounting they have on the Dually D2's, and the weatherproof automotive connector they're using.

Can't say enough good stuff about these parts....really solidly built.

20120218-IMG4193-X2.jpg

20120218-IMG4196-X2.jpg

20120218-IMG4247-X2.jpg

20120218-IMG4239-X2.jpg


I also got amber covers that snap on very securely for heavy snow/heavy dust situations to improve visibility. Here are pics with one of the covers in place, and general pics of the 40" e series main light bar.

20120218-IMG4256-X2.jpg

This next shot shows the lighting effect of snapping the cover on, vs the native color output
20120218-IMG4250-X2.jpg

20120218-IMG4204-X2.jpg

20120218-IMG4127-X2.jpg
 
OP
OP
C

coby

Full Member
Joined
Apr 24, 2003
Messages
317
Loc.
Fort Collins, CO
BTW, a number of this current batch of pics was taken by Brian Graves, another Bronco owner, who does some amazing work with landscape photography. I'm sure he'll pipe up and share a website if anyone's interested. I've always gotten a kick out of learning what other hobbies our bronco brethren have.
 

.94 OR

Contributor
Bronco Guru
Joined
Jul 5, 2009
Messages
2,215
Loc.
Willamette Valley, OR
Back to the story... something about your wife getting a "mod" done too. You are setting a precedence with high quality photos.

Fantastic work by the way.
 
OP
OP
C

coby

Full Member
Joined
Apr 24, 2003
Messages
317
Loc.
Fort Collins, CO
Back to the story... something about your wife getting a "mod" done too. You are setting a precedence with high quality photos.

Fantastic work by the way.

There'll be pics of that too when it's done. Right now she's looking at Sept for that mod....we thought it'd be before summer but the schedule ain't workin' out for that.
 

nik

Sr. Member
Joined
Dec 3, 2007
Messages
617
Loc.
Corcoran, CA
This build is sweet! One of the main reason I check the tech section daily, can't wait to see this stack of parts put together!:cool:
 
OP
OP
C

coby

Full Member
Joined
Apr 24, 2003
Messages
317
Loc.
Fort Collins, CO
Workin' on it. Bit of an update:

Aaron and Lane are workin' on building the frame and modifying the body. Lane's adding 5 or so inches of length behind the front seats, so we can keep most of the tail lights and the stock tailgate....I want it to keep the bronco look as much as possible. I've been fighting a bit with Whipple (who is HORRIBLE about calling back in any sort of good timeframe and delivering on order fulfillment) and the Hogan's intake custom intake, so that we get it right the first time.
Intake will have bungs for:
water temp 3/8" NPT
manifold surface temp 3/8" NPT blind hole
intake air charge temp 3/8" NPT, after intercooler in plenum
two 1/8" NPT bungs for vacuum/boost gauge and for MAP for Accel DFI (same thing, basically)
inlet for Snow Performance Methanol/Water injection. This is a backup idea...if the intercooler doesn't drop the air temp enough, then I'll add the Snow kit and inject before AND after the blower.

8 injectors. I ordered what I hope are extremely well matched, extremely low latency, high quality spray pattern injectors. Goal is to have steady idle and accurate fuel metering at low power levels as well as a high flow capability. The ones I chose are:
FiveO Black Ops 1000cc/min I may have gone a bit light for producing 1000hp at the crank if the bfsc is truly up around .65 or .70.....but with the intercooler, I'm hoping the bfsc comes in closer to an NA number of around .5 or .55.

Anyone want to start a pool on what breaks first? Could do two pools...engine and driveline. I'm wondering how well the crank will hold up personally...this is a modified 400 crank...the rods and pistons are very strong forged parts. Hell, might be block...we'll see. I've got another mill in mind if this one grenades.

Tranny is shipping tomorrow with any luck. Just got off the phone with Hughes about it..they're about a week late on it. They're welding on the billet adapter ring to the bellhousing now. However, I'm stoked about the custom 4l80e they're building for me and the custom torque converter. Should be pretty badass.

I do have other parts that have come in to post. Here's a couple:

This the dual sync billet distributor I'll be using with the Accel DFI...the dual sync lets me run this in SEFI mode.

20120218-IMG4139-X2.jpg


20120218-IMG4147-X2.jpg


20120218-IMG4154-X2.jpg


20120218-IMG4169-X2.jpg


20120218-IMG4170-X2.jpg


This is the cam sync ring; independently adjustable from the timing. I've not played with one before...kinda neat.

20120218-IMG4176-X2.jpg


This gear will have to get swapped for a brass one....the current cam in my motor chews these up and spits them out..which isn't good to have chewed up metal bits floating around in the oil. Lost two dizzy gears years back when I first put this cam in before I figured it out.

20120218-IMG4180-X2.jpg


That's all for now. More updates to follow.
 

AaronB

New Member
Joined
Jan 26, 2012
Messages
46
Loc.
Longmont, CO
So while working this morning, I thought it would be a good idea to play with on of my 4.5" grinders. That is until I lost... Got to spend a few hours in the local ER. Sliced my left index finger near my knuckle. Got it decently, even nicked the tendon. Guess that is kinda a big deal, at least they kept acting like it. They put 7 quick stitches in and put my left arm/wrist/hand in a cast till I can see the surgeon. Lane was nice enough to drive me to the ER, and take pics...

Here is me giving my "I am a big pansy" face at check in:
2012-03-02_10-31-34_851.jpg


and one of me giving ya'll the "salute":
2012-03-02_10-37-58_513.jpg


I won't post anything more gory than this, but if you want to see the rest of the photos, you can go here to check them out on google+
 

camomog

Full Member
Joined
Sep 10, 2008
Messages
254
Loc.
Reno, Nv.
It seams your a little board lately. I thought you took a lot of light pictures but then came the dist. and its pict's. Lots of cool parts though and hope the hand doesn't need anything major.
 

Quick & Dirty

Sr. Member
Joined
Feb 15, 2004
Messages
857
BTW...the camera you use doesn't matter as much as you think....but getting good lighting is pretty damn important.

I posted some close-up pics I took on another forum, and someone asked what set-up I used. Uhh... an 8 year old pocket point-and-shoot. Good lighting and a steady hand are key. As well as taking a lot of shots and picking the ones that turn out.
 
Top