• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Bouncing Speedometer Needle

Bulletman

Full Member
Joined
Dec 5, 2009
Messages
245
So, what is the cause of my bouncing speedometer needle? It ONLY does this at less than 30 mph, at any speed above 30 it is smooth as it should be. Cable? The unit itsself?
 

Lmfp

Bronco Guru
Joined
Jun 28, 2011
Messages
1,496
Loc.
Lake Charles, LA
Your cable probably is in a bind. Make sure any curves are big and sweeping to keep it from binding. Thats usually the problem.
 

NicksTrix

Bronco Guru
Joined
Aug 1, 2001
Messages
6,410
the head could also need a tune up. classychassisrestoration.com does a great job servicing and updating these old units. kevin is also a member here known as Fallingdown.
 

Quick & Dirty

Sr. Member
Joined
Feb 15, 2004
Messages
857
Probably needs to be greased. While it's out of the housing, check for any frayed strands that could be hanging up.
 

Bronco Junkie

So Cal Broncos
Joined
Feb 29, 2012
Messages
3,246
Mine was doing that too along with some sort of grinding noise. It probably just needed some grease but I just bought and installed a new one from WH.
 

hollowch

Sr. Member
Joined
Jul 15, 2010
Messages
607
Loc.
Midland, TX
Most likely, your speedo cable needs to be lubricated. Disconnect the speedo cable from the back of the speedometer, and pull through the firewall. You can buy speedometer cable lubricant at almost any autoparts store (I know Oreillys sells it). Tell them you're looking for graphite lubricant. It is just graphite suspended in a solvent, to help wash it down the cable housing. Do not use oil, WD-40, etc. It will make the problem worse.

I had the same problem, and used lots of that lubricant on my old one... The problem could not be solved though because there was just too much gunk in my cable. I had to buy a new one.

NOTE*** it might be a good idea to get some carburetor spray cleaner and just spray that stuff down the cable and loosen all that gunk up. Just be sure if you do that, that you disconnect the other end of the cable from your transfer case, because you don't want that stuff leaking into there.

Or you could just say, whatever and order a new one for $20 -- http://www.tomsbroncoparts.com/product/speedometer-cable-66-77-early-ford-bronco-new
 

Explorer

Bronco Guru
Joined
Mar 2, 2008
Messages
4,390
Loc.
Raphine, Virginia
Yeah, more than likely the cable. But, someone correct me if I'm wrong, but I "vaguely" remember the needle is magnetically dampned too.
 

hollowch

Sr. Member
Joined
Jul 15, 2010
Messages
607
Loc.
Midland, TX
Yeah, more than likely the cable. But, someone correct me if I'm wrong, but I "vaguely" remember the needle is magnetically dampned too.

I believe you're correct... but I don't think if that was faulty, it would result as a bouncy speedo needle. That indicates something getting binded & released..

Bulletman: Does it bounce up to a certain speed? Mine bounced up to about 40 mph and then stopped.
 
OP
OP
B

Bulletman

Full Member
Joined
Dec 5, 2009
Messages
245
Mine bounces UP TO and DOWN FROM 30 mph,,,,,,,,,anything over 30 and it's smooth as butter !
 
Top