• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Bronco Hunting

Schloer2

Full Member
Joined
Mar 9, 2012
Messages
268
I am a noob that is headed to check out a 1977 Bronco on Sunday. Seller says it was a running/driving/licensed rig in 2002 when he parked it in his barn and it has not moved since. I know what to look for in terms of rust, but am by no means a mechanic. Any recommendations on what to check on the drivetrain to indicate whether it can be brought back to life with new plugs/fluid/fuel? The odometer shows 86k miles, but the engine is actually a newer 302 out of a mid-80’s Mustang ( unknown mileage).

Also, is there any risk with clamping on some jumper cables to quickly check if any of the electrical still works?

Thank you for any words of wisdom...just trying to avoid buying a rig and then sinking $$$$ into the engine.
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
I wouldn't hesitate to put jumpers on it. I would pull the coil wire off and crank it for awhile before you start it though- check fluids.

Kyle
 

Crawdad

Bronco Guru
Joined
Feb 16, 2011
Messages
3,635
Be careful the tank might be full of sludge. If it turns then that's a good sign. May blow some smoke but that's to be expected. "Should" clear up with oil change and new gas. Just want to make sure engine is not locked up. Manual tranny usually do well if sat for long periods of time, can't say the same for autos.
 
OP
OP
Schloer2

Schloer2

Full Member
Joined
Mar 9, 2012
Messages
268
I wasn't planning on trying to fire it up. Just try to turn the engine manually and check the oil to make sure it isn't dry. I figured I would throw on the jumpers just to see if any of the lights/signals/horn/wiper motors/etc were in working order. Unfortunately, it is an auto trans...what do I need to be concerned about Crawdad?
 

beernut

Full Member
Joined
May 26, 2011
Messages
266
Loc.
Hampton
I wasn't planning on trying to fire it up. Just try to turn the engine manually and check the oil to make sure it isn't dry. I figured I would throw on the jumpers just to see if any of the lights/signals/horn/wiper motors/etc were in working order. Unfortunately, it is an auto trans...what do I need to be concerned about Crawdad?

Mostly oil turning to sludge, valve body becoming gummed up, maybe the torque converter. Really though, the ford c4/c6 are easy to find. I don't believe you'll have any problems with the transfer case as long as it shifts.
 

half cab

Contributor
Guru Bronco
Joined
Dec 8, 2010
Messages
16,311
I would think that C4 would be ok....If everything was buttoned up and not exposed to the weather as long as it was ok before parked...
 

Spartan

Sr. Member
Joined
Feb 3, 2013
Messages
425
Loc.
Backwoods, KS
That was my thought as well half cab, ex. If windows were missing and it sat outside in the Minnesota winters etc
 
OP
OP
Schloer2

Schloer2

Full Member
Joined
Mar 9, 2012
Messages
268
In IL in a shed with concrete floors. Hardtop and doors all in tact. Only real rust issues seem to be rear quarter seams and passenger floor pan.
 

Spartan

Sr. Member
Joined
Feb 3, 2013
Messages
425
Loc.
Backwoods, KS
Should be pretty clean then as long as the varmints left it alone lol
May not be a bad idea to prime the oiling system after you change it so you know there's oil in the top end prior to it cranking/firing it.
You'll need to rebuild the carb.
Also the trans may leak at first but *sometimes* the seal can swell and seal again (as long as they're in good cond) after you change the filter/fluid in the trans and start driving it again.
You'll def want to change the diff fluids and t-case fluids, theres probably condensation in them that has created a thin layer of surface rust.
Axle seals will probably leak, *probably*, as well as most gaskets/seals but its really not that big of a deal as long as you're willing to get dirty lol
 
OP
OP
Schloer2

Schloer2

Full Member
Joined
Mar 9, 2012
Messages
268
Thanks everyone for your insight. I have been searching for over a year now and hope this is finally the right rig for me.
 

half cab

Contributor
Guru Bronco
Joined
Dec 8, 2010
Messages
16,311
Good luck with it and keep us posted.

If priced right and you get man you know this site can walk ya through any issue that might come up....;)
 

sprdv1

Contributor
REBEL
Joined
Mar 8, 2007
Messages
81,996
Thanks everyone for your insight. I have been searching for over a year now and hope this is finally the right rig for me.

Patience is key.. The right one will come along for ya
 

broncosam

Bronco Guru
Joined
Feb 8, 2005
Messages
1,188
Before I bought my first Bronco, I went to look at one in Tennessee, it had been sitting awhile. First thing I did when I opened the hood was to pull the crankcase dipstick, it wasn't pretty. The stuff on the dipstick was milky and smelled of gas, I passed on it.
 

luke

Sr. Member
Joined
Sep 19, 2010
Messages
370
illinois?! thats my country. where is it? where is it? where is it? just kidding. good luck. hope you get a good one.
 

Punisher

Sr. Member
Joined
Nov 25, 2004
Messages
505
Thank you for any words of wisdom...just trying to avoid buying a rig and then sinking $$$$ into the engine.

Well if you do get it no matter what shape it's in if the bronco bug bites and it usually does plan on sinking $$$$ into it anyway. :)
Good luck.
 
OP
OP
Schloer2

Schloer2

Full Member
Joined
Mar 9, 2012
Messages
268
A couple teaser pics - obviously gonna need some wheels/tires

3m53Ld3I55N55Gc5K7d26cd9295407bd316a1.jpg


3Mc3Fd3He5E15F45Mcd260c058c3a34201cec.jpg
 
Top