• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Bronco won't start

LSUpete

Contributor
Bronco Guru
Joined
Jul 11, 2001
Messages
2,065
Drove the Bronco for an hour on the highway and pulled over to get something to eat.....now it won't start. Headlights work and I can hear the electric fuel pump, but I get nothing when I turn the key.

Thoughts?
 

moses_m

Full Member
Joined
May 5, 2013
Messages
262
Does it sound like it wants to start or does it just turn over and over?
remove gas line to carb. Have someone turn on key and see if gas is getting to carb. Use a small bucket or catch can.
 

SSDDBRONCO

Bronco Guru
Joined
Nov 12, 2009
Messages
2,172
Loc.
Los Angeles
Drove the Bronco for an hour on the highway and pulled over to get something to eat.....now it won't start. Headlights work and I can hear the electric fuel pump, but I get nothing when I turn the key.

Thoughts?

Do you have any spark? Check if everything look normal with the distributor cap. Just a thought from one of my no start experiences lol.
 
OP
OP
LSUpete

LSUpete

Contributor
Bronco Guru
Joined
Jul 11, 2001
Messages
2,065
Naw man....it's not fuel related. The key is just dead. I was thinking my nuetral safety switch might be bad.
 

moses_m

Full Member
Joined
May 5, 2013
Messages
262
I saw you have a painless wiring harness. Have you checked maxi fuse? If you think its the neutral switch have you tried jumpering it out (bypassing)?
 

half cab

Contributor
Guru Bronco
Joined
Dec 8, 2010
Messages
16,311
Wiggle the shifter n turn the key but I'm sure you already tried this .
 
OP
OP
LSUpete

LSUpete

Contributor
Bronco Guru
Joined
Jul 11, 2001
Messages
2,065
I saw you have a painless wiring harness. Have you checked maxi fuse? If you think its the neutral switch have you tried jumpering it out (bypassing)?



It's probably not the maxi-fuse....sinvce all of the other electrical items are working.
 
OP
OP
LSUpete

LSUpete

Contributor
Bronco Guru
Joined
Jul 11, 2001
Messages
2,065
Wiggle the shifter n turn the key but I'm sure you already tried this .


Yep, I tried that. I also checked the linkage and the safety switch. Both are tight with no play or indication that anything is wrong.
 

moses_m

Full Member
Joined
May 5, 2013
Messages
262
ok check coil fuse 20 amp I believe. Wire 919 is ignition to switch too solenoid. Also check if anything is loose behind ignition switch.
 

Joe473

Sr. Member
Joined
Jul 16, 2012
Messages
958
Jump it at the solenoid to try and start and get home. Just check for shorts and ground first.
 

Joe473

Sr. Member
Joined
Jul 16, 2012
Messages
958
Make sure u are not in gear. Small jumper from positive battery terminal to s lead on solenoid. If solenoid is good engine will crank. Make sure key is in run to start. There are two terminals on solenoid s and I. S pulls in the relay to send crank power to starter. I terminal goes to power the coil through the ignition switch.
 
OP
OP
LSUpete

LSUpete

Contributor
Bronco Guru
Joined
Jul 11, 2001
Messages
2,065
Make sure u are not in gear. Small jumper from positive battery terminal to s lead on solenoid. If solenoid is good engine will crank. Make sure key is in run to start. There are two terminals on solenoid s and I. S pulls in the relay to send crank power to starter. I terminal goes to power the coil through the ignition switch.

What do I use for a"small jumper"?
 

moses_m

Full Member
Joined
May 5, 2013
Messages
262
making the S and I on the soleniod meet with a small wire or wrench. Warning it will spark make sure bronco is in park or neutral.
 

Joe473

Sr. Member
Joined
Jul 16, 2012
Messages
958
14 guage wire has worked for me to spin engine for compression check and such.. you could use jumper cables. VERY carefully not shorting to ground anywhere on fender or solenoid. S terminal is small so be careful
 

Teal68

Contributor
Bronco Guru
Joined
Mar 28, 2013
Messages
2,679
Loc.
Inlet Beach
I always use a screwdriver. Touch the tip to one and tilt until the shaft hits the other. Like others said, Key to on run position and make sure it is not in gear!
 

zonian

Sr. Member
Joined
Nov 5, 2013
Messages
764
Loc.
St. Augustine
What the other guys said, just use a screwdriver to cross the two terminals on the solenoid with key on....should crank right over. I've been through 2 neutral safety switches in last years, both TBP and BG sell them at reasonable prices, much cheaper than I found at the local autozone. A shop will charge you much more. I have no idea why mine have gone, but now I carry a spare in the back. Jumping the solenoid will get you home.......
 
Top