• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Carb hangs up

VanWelder

New Member
Joined
Mar 13, 2018
Messages
36
I have an issue with my 2bbl carb throttle hanging up where ever I raise the idle to. I have eliminated the linkage and run the engine from under the hood. It feels like it’s binding but when I shut my rig off, it works freely. I’ve lubed the rod and parts associated with the butterflies with no resolution.
This is what have:
68’ U15
289
3sp
Carb is brand new but for a 76’ U15 with a 302/auto trans and electric choke
Is the difference in years the problem?
I’m not computer savvy. I have a video of it that I would like to post. Not sure how, so any guidance with that would be beneficial.
Thank you
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
Since no '76 2150 carburetors have built since '76, I have to wonder if what you have is ChiCom knock off. The ChiComs haven't attempted to make 2100 carbs that Ford used in '68s. I'm also interested in what you mean by eliminating the linkage. Did you simply disconnect the throttle rod from the bell crank on the intake, or did you do something else? Without a linkage the only place for friction or binding is the throttle shaft.That would be surprising. Also from you're description you may just have the fast idle cam holding the throttle open as it was designed to do.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Also from you're description you may just have the fast idle cam holding the throttle open as it was designed to do.

Thinking the same thing as jckkys. Not only just as designed though, since even with lube they can hang up if not adjusted properly by the builder, or from a rough surface or whatever. Might be even more common with the new imported stuff too.
When you lubed the linkage VanWelder, did you also get some lube up in the choke mechanism?
Is the choke plate/butterfly fully open when this is happening? Maybe the choke coil is set too rich and not fully opening up, or not opening up in a reasonable time.

By the way, what type of lubrication are you using? Seems like something thick and gooey is going to cause you more trouble down the line when it attracts dirt and dust and junk.
I don't know that for a fact, but it seems like it might be an issue.

Do you lube carb linkage jckkys, or clean it now and then and leave it dry?

Paul
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
When an automatic choke is cold, the choke plate tries to partly or completely close before you touch the accelerator. When depressing the gas pedal, the choke plate closes and the fast idle cam moves. That holds the throttle partially open. This is just a part of the cold start procedure on engines with automatic chokes. If the throttle shaft is binding on a new ChiCom carb, return it as a defective part.
 
OP
OP
V

VanWelder

New Member
Joined
Mar 13, 2018
Messages
36
The linkage/rod is disconnected from carb to narrow down the root of the problem. Keep in mind it only does it when running. I can manually rotate throttle on side of carb and it will stay where I stop unless it’s wide open, then it will spring back. When it not running, the throttle springs right back. If I can figure out how to upload the video, I could better explain
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
When the engine is running, there is intake manifold vacuum pulling down on the throttle plates that could cause them to bind if there is rust or some other ruff surface on the bottom of the shaft or the bore it rotates in. The downward pressure from intake vacuum goes away with the engine shut down allowing the shaft to rotate. Rusty throttle shafts are common on carbs left outside exposed to the elements.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
I'm guessing that an extremely accurate restoration wasn't the goal when he bought a ChiCom 2150 carburetor with an automatic choke. The Bronco is a '68 when anti-dieseling solenoids didn't exist. The '68s had 2100s with manual chokes.
 
OP
OP
V

VanWelder

New Member
Joined
Mar 13, 2018
Messages
36
My mistake…
I have a rebuilt factory 2150 with auto choke. I’m using a 76 harness. I used this carb because I will eventually use a C4 and wanted the wires to hook up as well as the carb linkage for the kickdown.
I have been running it with the aluminum spacer under the carb. I’ve eliminated it and hooked the PCV the the back of the carb. Seems to have corrected itself other than running rich.
Maybe the problem was the spacer increasing vacuum and holding the throttle open?
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
for running rich pop the top and check the float setting and the main jet sizes ford used 46 to 52 jets in broncos. very high altitudes 46 and low altitude 52 and everything in between since its a rebuilt it could be anything make sure the 2 jets are the same size that is why its never recommended to replace your stock bronco carb. Bronco carbs came with 1.08 venturi size is that what is cast on the drivers side of your carb?
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
I have no problem with the solenoid. I have one on my '66 1.08 venturi 4100. I wire it with a rocker switch to increase RPMs on very bumpy roads to eliminate bump stall when the throttle is closed. My tune ie lower curb idle eliminated the dieseling after shut down. So it's not needed for the original purpose. The jets determine the A/F ratio cruising. So different jets may be needed to lean that out. New jets are less expensive here;https://allcarbs.com/product/motorcraft-ford-autolite-main-jets/.
 
Top