• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Dana 44 knuckle removal help

bronko69er

EB Addict
Joined
Oct 16, 2006
Messages
4,599
Loc.
Renton, WA
Assuming you took the 6 nuts off that hold the spindle to the knucle.....
It a pretty tight fit.
Is this the disc or drum axle?
More importantly, are you dealing with a drum backing plate under the spindle or a caliper bracket?
I usually take my cold chisel and a hammer and tap around the circumference in the gap beween the spindle and the caliper bracket. This has always worked for me. I haven't actually done this with a drum backing plate so it may be a little harder to get to the gap.
 

ugly74

Bronco abuser
Joined
Apr 17, 2006
Messages
2,856
Loc.
Colorado
hit the sides of the spindle with a rubber mallet, that'll do it.
or if you don't have a rubber mallet, use a block of wood and a hammer.
 

flousberg

Sr. Member
Joined
Apr 28, 2002
Messages
774
One I pulled out of a junk yard was a real PITA. I had to use a 3 lb hammer and a chisel to get it off. It you have everything apart, you may be able to get a punch on the backside of it and drive it out. When you put it back together, take some emery cloth clean it up and put on antisieze.
 
OP
OP
JohnJohn

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
Thanks guys.
I do have the 6 backing plate bolts off and the backing plate is removed. This is a drum diff.

I don't think it has ever been apart so I am dealing with years of rust.

I have tried a rubber mallet, a 5 pound sledge and an air hammer with no luck yet. I have used about a half of a bottle of PB Blast.

The ball joint shafts look like some hard metal. My sawzall barley scratched the ball joint shafts so I am going to use my angle grinder with a cut off wheel to cut the shafts. It also looks like I will need to buy a 6" angle grinder to get enough reach to get to the lower ball joint shaft. My 4" just cant get over the knuckle.

You can bet I will be coating any spindle or drum with antisieze when I put this back together.
 

bronko69er

EB Addict
Joined
Oct 16, 2006
Messages
4,599
Loc.
Renton, WA
If its on the bronco, which I think you said its not, you could try putting a jack under it and lifting, just to see if it will break loose. Put a block of wood under it so the jack doesn't damage the spindle. Just lift a hair off the jack stand and try beating on the flange next to the studs. I bet that would work....
 
OP
OP
JohnJohn

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
Thanks guys.
Yes it is off the truck.

I actually tried something similar to how the spindle puller works. I first put both spindle nuts back on the spindle, then I took a 3 arm puller and set it up to pull the spindle nuts while pushing the Axel in.
It pushed the Axel into the Axel tube pretty hard so I stopped. My method should work like the spindle puller but it is good to know there is a tool to help.
I will try the 3 arm puller again after hitting it with some more heat and PB Blast.
I will give this another try before I go back to the ball joints.

I have another dana 44 next to this one but it has the disk breaks. My goal is to put the disk knuckles from my 3.50 D44 over to this 4.10 D44.
 
OP
OP
JohnJohn

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
I GOT IT!!!!!!

I used a 3 arm puller to put pressure on the spindle, then used a gasket scraper and a 5 pound sledge to start the separation of the spindle. Once I got just a small gap, I put put more pressure on the puller then worked around the spindle with more PB Blast until it popped off.

Where there is a will there is a big hammer.

Now for the other side. :(

Thanks guys. Maybe this post will help someone else one day.
 
Top