• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Dana 44 swap...again

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Alright guys I know this has been beaten to death, and I used the search feature, but didn't find what I was looking for.

For someone with little to no experience with axles. What I'm I looking for in a d44? I know the bronco axles are narrowed so where can I find what I need?

The axles themselves, do I need to go straight to a higher spline axle or will whats in it work? I'm not going to be rock crawling, more like trails and creek bed type stuff. I'm running 35's so from what I've read, the d30 won't hold up.

Like I said I know this has been talked about numerous times, so if that information is somewhere in here just point me in the direction! Thanks again for all the help guys, this forum has been invaluable so far!
 

67bondobronc

Sr. Member
Joined
Nov 14, 2002
Messages
867
As was said you will need the entire thing (housing and axles). If you have already completed a disc brake conversion you can switch that over to the D44.

I found my D44 on the classifieds on here for a real good price. I would just run what you have and keep checking the classifieds, evilbay, and craigslist for a D44. The EB parts houses like their D44's a little too much for my budget. But as you said, 35s on a D30 is pushing the envelope a little hard.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
I keep trying to research what I need to do and my head just ends up spinning! between gearing, housings, 3rd members, axles and lockers I'm more confused now then when I started!
 

brtxbronco

Contributor
New Member
Joined
Jun 24, 2005
Messages
31
your replacement D44 will need the same gear ratio as the rear axle of your rig. if not then you will need to change one or the other to match,when doing that change is a good time to add a locker/ limited slip diff.Also when doing the D44 swap I would go to disc brakes if not already installed and you may want to upgrade the steering linkage or tie rod over. upgraded axle shafts are avail. at all the bronco venders. lots to think about when doing this swap
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
I keep trying to research what I need to do and my head just ends up spinning! between gearing, housings, 3rd members, axles and lockers I'm more confused now then when I started!
It really isn't as confusing as it seems. But, there are some decisions to be made.

The only Dana 44 housing that will fit an EB without modification is a Dana 44 from another EB. A second choice would be a full width housing from a f150, that you might decide to narrow, usually on the passenger side, to make it the same as an EB housing. But a lot of those are high pinion, which may cause some interference underneath, unless you're running a big lift. f

I ran a stock EB Dana 44 with 3.50 gears and an open carrier with 35's, and never broke an axle. That may be due in part to the open carrier. If you run an open carrier in front, and keep your foot out of the gas, the stock axles may hold up just fine. You may opt to upgrade the stock axle u-joints to help make things last a little longer, as the issue is quite often a broken u-joint which takes out the axle at that point.

Gearing is strictly up to you, your intended use and the rest of your drivetrain. Here's a gear calculator which should help decide what gear ratio is best for you. http://www.grimmjeeper.com/gears.html

Also it's up to you to decide what "locker", if any, you want to run. You may decide that an open carrier is just fine. I'm always amazed at how well my Bronco performs without the front axles locked. If you decide to do something in the front, a limited slip, clutch-type carrier may be best. For the type off-roading I do here in Arizona, I decided a selectable locker was best for me. It was at that time I decided to upgrade axle shafts.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Wow, thanks. That actually cleared things up a lot! I looked around at some of the vendors and they're asking way too much. I guess I'll just wait for one to pop up on here. Thanks guys! :cool:
 

markperry

Bronco Guru
Joined
May 8, 2009
Messages
4,175
Okie69, try contacting Siderbox on this forum. He has a few laying around, he might work with you. He lives in Gardner Ks, a few hours from you.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
I picked up a narrowed HP D44 from Matt at Vintage Iron Works. Now I just gotta get it home and get to work on the rig!
 
Top