• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Different Size Windshield Knob Bolts?

Audifan

Contributor
Full Member
Joined
Nov 25, 2018
Messages
250
I just got my Bronco back from paint and body and my windshield frame was bad so we replaced it with one from a 76 (I think).

Everything was great until I took the new windshield knobs I had ordered from WH out of the package only to find out that they don't fit.

These are what I ordered:
https://www.wildhorses4x4.com/product/Billet-Aluminum-Windshield-Knobs-BLACK/bronco_Windshield_Parts

But the bolt on the knobs is too skinny (width/diameter) to engage the threads in the windshield frame.

Are there different sized windshield bolts?

Right now I've got $60 knobs that are useless, and a windshield that I can't bolt into place.
 

EricLar80

Bronco Guru
Joined
Jun 14, 2001
Messages
2,170
They should all be the same for 66-77. What size did they send you - can you measure it? Do you have the old bolts to compare them to?
 

triracer67

Contributor
Sr. Member
Joined
Nov 29, 2010
Messages
672
I wouldn't be surprised if they were replaced. My '67 threaded fittings had fallen into the windshield frames when PO must have tried to loosen them to move windshield. Double check there is actually a threaded "nut" inside the frame.
 

rguest3

Bronco Guru
Joined
Dec 13, 2012
Messages
3,780
Either the threaded mounting holes have been re-tapped larger, or the Bolts delivered to you are the wrong size.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Bolts the same unless someone has modified something. Broken bolts in the windshield frame is super common
 

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,122
Loc.
Cuchara, CO
My guess is the captured nuts have broken loose. Only fix is to cut out the area around the nuts, reinstall the nuts and weld a patch. Not a good option for a Bronco just out of paint! If you are running a hard top, the top will keep the windshield frame in place and you really don't need the bolts. If you are not running a hard top then install a front cage with braces to the windshield frame and again, you really don't need the bolts.
 

Timstrk

Full Member
Joined
Apr 8, 2014
Messages
198
Can you use a nutsert? Captured nut without the welding. Come in stainless steel, too.
 

bronkenn

Contributor
Bronco Guy
Joined
Apr 27, 2017
Messages
2,717
Loc.
Southeast Ohio
Looking at those knobs I don't think it would be to difficult to remove the 3/8 stud and drill and tap to the correct size stud.
 

WILDHORSES

Sponsor/Vendor
Bronco Guru
Joined
Nov 7, 2003
Messages
2,253
Loc.
USA
I bolted a frame in Monday 3/8" x 2 1/2" NC bolt and washer. Works 66-77.

I have never tried to modify the knobs but it might not be hard to do. If someone had used a larger bolt you could go that route. Check and see what size you need or maybe the hole is just stripped out. You can even use 3/8" fender clips on the frame but that would take some work too.

Jim
 
OP
OP
A

Audifan

Contributor
Full Member
Joined
Nov 25, 2018
Messages
250
Thanks guys, this was for sure an unforseen problem. Hopefully I'll have some time today to get out in the garage and mess with it.

Welding new bolts onto the billet knob should not be a problem as long as I can find the right bolt.
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
Thanks guys, this was for sure an unforseen problem. Hopefully I'll have some time today to get out in the garage and mess with it.

Welding new bolts onto the billet knob should not be a problem as long as I can find the right bolt.

Just went out and looked at my WH silver knobs.
There is a set pin that holds the bolt into the knob, seems like it would be an easy thing to do to just pop out the pin to swap bolt size. If that is the case...

Doug
 
Top