• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Disk brake conversion with drum knuckles

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
I currently have a D44 with front drum brakes on my trail rig. I also have a set of 77 disk knuckles and spindles ready to install.
I want to convert the front to disk but I don't want to replace my steering linkage yet and that is required with the wider 77 knuckles.

Can I use the 77 spindles on the drum knuckles and just grind down any clearance issues I may have with the knuckles?

As you can see I am trying to do this on the cheep.
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
Wilwood bronco kit re-uses all drum brake hardware. Don't take spindles off or anything. It's spendy, but with 6 piston calipers you don't need power assist. Steering stays the same.
 
OP
OP
JohnJohn

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
it sounds like I just need to step up and change the linkage to use the 77 knuckles.
 

SteveL

Huge chevy guy
Joined
Jun 24, 2001
Messages
11,969
Loc.
Hawthorne ca
Get the 78-79 knuckles out swap. Then you just need the bc tie-rod bushings to use your stock linkage
 

sykanr0ng

Bronco Guru
Joined
Aug 11, 2014
Messages
5,363
Alternative to that is the conversion using Chev. six bolt spindles and calipers which fit the Ford knuckles and use Ford hubs and rotors.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
As was said the GM conversion is probably going to work out cheaper. As your 77 route will also require new ball joints as well as the steering linkage and depending on your wheels may require wheel spacers.
 
OP
OP
JohnJohn

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
Thanks guys.
I have the 77 spindles, caliper brackets and knuckles.
I had estimated I need roughly $500 in additional parts to do the conversion not including the steering linkage.

I am running 16.5" Humvee H1 beadlocks with 37's. With 3.5" of backspacing I have plenty of room to clear things. I just don't want to have issues stopping on steep hills.
I will have to do the math but does anyone know roughly how much the Chevy disk conversion runs?

It looks like my 77 knuckles will run me around $800 in parts now inckuding steering linkage.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
You can get away with just replacing the tie-rod, and two ends with something like this: http://www.wildhorses4x4.com/product/Tie_Rod_2way_Adjustable_7677yr
It reuses the stock draglink, but replaces the also-weak tie-rod with a much beefier one of the correct length and size rod end.

The downside of not doing the draglink too though, is that you don't gain that extra adjustability that lets you fine tune your steering box's on-center position. But that might not be a deal breaker at this point.

Frankly, with 37's your stock tie-rod is a weak link worth replacing anyway. Never mind that it adds cost, it's just cheap insurance if you expect to use 4wd to any extent.

Paul
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
A complete GM kit from the vendors will cost you around $550. But it shouldnt be to hard to find a GM d44 at a junkyard or craigslist that you can get the caliper brackets, spindles and calipers off of for next to nothing. You might even look thru our classifieds people sell those parts quite often. Then all you would need is 76up ford hubs and rotors some brake lines and maybe new seals and bearings. Of course new calipers and brake pads but that will be about it.
 
Top