cougarmandan
Sr. Member
I installed some new door hinges today and the door is way off. If you want to skip to the technical part, skip the next 2 paragraphs, if you want the typical story of how my projects go, then go ahead and read them.
Ok, I have been playing with the bronco and started working on doors. I thought would be a good place to start with body work. My thinking being I might knock them out before I replace the rocker and floor pans so I will have an extra reference for lining up stuff. I removed the hinges and tried to replace the pins. They are worn out and the pins does not what to budge. What a waste of a day. I only got one hinge apart and i bent it doing so. Anyways, after that I decided it would be well worth the money to buy new hinges. I looked on several website and found that I liked the rugged James Duff set with the half inch pin that allow for lift off door removal. I ordered them last week and got them this weekend.
Today I decided to play with it. I already have the drivers door off and the hinges off. Side note, the hinge screws on a 68 use a pozidriv 4 to remove them, not a Philips. However, the fender uses Phillips 3 or 4 (I can't remember). I bought a Matco impact driver and it had been an invaluable tool for removing those screws. It has all the bits and you can put the bit in the screw head and the pozidriv bites so much better. For this project it takes 6 hammer wraps to get the screws to turn easy. I also soaked them with wd-40 a few times over the course of a couple of days. Anyways, there was bare unrusted steel under the hinges so I decided to clean it up with a wire wheel and primer it. I wound up taking the beat up old fender off too. It actually when pretty smooth all things considered. After the paint dries, I start threading the bolts in and they start out fine but get tight about 1/8th inch before tightening down. the last bolt, brand new mind you, snaps off, about flush with the backing plate. I drilled a hole in it and put an extractor I have used a dozen or so time and this time it decided it was time to snap. Yip, a hardened steel tip of an extractor in the middle (sorta) of my broken bolt. I wound up messing with it for several hours. I tried to outsmart it by drilling a small hole next to it and maybe get the smaller easy out. It just didn't work. It dulled out several nice drill bits trying to drill beside in the broken piece. I then took some diamond grinding bit I bought at harbor freight for my dremel tool. It worked very slowly, but I couldn't get the hole any deeper, just wider. I was able to get the rest of the extractor in the hole, but it just wouldn't bite. I was trying to get the hole a little deeper so I was grinding some more when the diamond ball tip comes off the bit. The hole diamond encrusted ball just slips off the end of the bit. WTF man. You know how you drill that out, well, let me give you a hint, its not another diamond bit. The answer is, you don't. SO drilled a half inch hole on the back side of the post (which is really the front side) in the wrong spot by half in inch and redrilled it in the right spot. So much for measuring twice, maybe I'll give it a try next time. I drilled a small hole in the broken bolt from the back side which allowed me to get an awl in there and knock out the harden steel and diamond all in one wrap. I mess with trying to get the extractor to work, but it just isn't going to. At that point I decide to drill a hole and tap it. Well, It grabbed at the last second of drilling and shattered my 1/4" drill bit. Well, as I was starting the tap, the remainder of the bolt threaded its way out so all is well there. I ran the tap down all the bolt holes so they all work nice and smooth. I guess I will be running to Atwoods for some grade 8's tomorrow. I went ahead and bolted the hinges on the door and posts. Its a whole heck of a lot easier than holding the door while you try to get the bolts in.
So, got the hinges on and loose enough I can move them around. I hang the door and go to check the striker alignment and its a good 3/4" up in the back. I tried to move the hinges around to get it down and it ain't moving. Is this normal? What causes this? What the procedure to make it right? I did some searching, and the best I found was putting a 2x4 on the post and beat with a rubber hammer. Woundn't that mess up the alignment with the fender. I was thinking of using a shim of some sort. The fender was beat to hell, but the inner panel looks ok so I didn't think that it had too major of a wreck. The bottom of it has been bent over I assume to increase tire clearance but I didn't see anything to make me think it was something transferred on up to the door post. The door with the old hinges probably sagged a half inch so I was a little surprised. The hinges are all the same aren't they? I took some pics and uploaded them to photobucket, but they are down for site maintenance right now so I can't share them.
Also, the James Duff hinge set didn't come with door strap brackets and I can't seem to find them commercially available for lift off doors without buying the whole set. Are you uuys making your own? I was thinking of taking a 3/8th rod and heating it/beating it flat for about 2 inches and making a U for the strap part go on. Drill some mounting holes.
Photobucket is back up!
Ok, I have been playing with the bronco and started working on doors. I thought would be a good place to start with body work. My thinking being I might knock them out before I replace the rocker and floor pans so I will have an extra reference for lining up stuff. I removed the hinges and tried to replace the pins. They are worn out and the pins does not what to budge. What a waste of a day. I only got one hinge apart and i bent it doing so. Anyways, after that I decided it would be well worth the money to buy new hinges. I looked on several website and found that I liked the rugged James Duff set with the half inch pin that allow for lift off door removal. I ordered them last week and got them this weekend.
Today I decided to play with it. I already have the drivers door off and the hinges off. Side note, the hinge screws on a 68 use a pozidriv 4 to remove them, not a Philips. However, the fender uses Phillips 3 or 4 (I can't remember). I bought a Matco impact driver and it had been an invaluable tool for removing those screws. It has all the bits and you can put the bit in the screw head and the pozidriv bites so much better. For this project it takes 6 hammer wraps to get the screws to turn easy. I also soaked them with wd-40 a few times over the course of a couple of days. Anyways, there was bare unrusted steel under the hinges so I decided to clean it up with a wire wheel and primer it. I wound up taking the beat up old fender off too. It actually when pretty smooth all things considered. After the paint dries, I start threading the bolts in and they start out fine but get tight about 1/8th inch before tightening down. the last bolt, brand new mind you, snaps off, about flush with the backing plate. I drilled a hole in it and put an extractor I have used a dozen or so time and this time it decided it was time to snap. Yip, a hardened steel tip of an extractor in the middle (sorta) of my broken bolt. I wound up messing with it for several hours. I tried to outsmart it by drilling a small hole next to it and maybe get the smaller easy out. It just didn't work. It dulled out several nice drill bits trying to drill beside in the broken piece. I then took some diamond grinding bit I bought at harbor freight for my dremel tool. It worked very slowly, but I couldn't get the hole any deeper, just wider. I was able to get the rest of the extractor in the hole, but it just wouldn't bite. I was trying to get the hole a little deeper so I was grinding some more when the diamond ball tip comes off the bit. The hole diamond encrusted ball just slips off the end of the bit. WTF man. You know how you drill that out, well, let me give you a hint, its not another diamond bit. The answer is, you don't. SO drilled a half inch hole on the back side of the post (which is really the front side) in the wrong spot by half in inch and redrilled it in the right spot. So much for measuring twice, maybe I'll give it a try next time. I drilled a small hole in the broken bolt from the back side which allowed me to get an awl in there and knock out the harden steel and diamond all in one wrap. I mess with trying to get the extractor to work, but it just isn't going to. At that point I decide to drill a hole and tap it. Well, It grabbed at the last second of drilling and shattered my 1/4" drill bit. Well, as I was starting the tap, the remainder of the bolt threaded its way out so all is well there. I ran the tap down all the bolt holes so they all work nice and smooth. I guess I will be running to Atwoods for some grade 8's tomorrow. I went ahead and bolted the hinges on the door and posts. Its a whole heck of a lot easier than holding the door while you try to get the bolts in.
So, got the hinges on and loose enough I can move them around. I hang the door and go to check the striker alignment and its a good 3/4" up in the back. I tried to move the hinges around to get it down and it ain't moving. Is this normal? What causes this? What the procedure to make it right? I did some searching, and the best I found was putting a 2x4 on the post and beat with a rubber hammer. Woundn't that mess up the alignment with the fender. I was thinking of using a shim of some sort. The fender was beat to hell, but the inner panel looks ok so I didn't think that it had too major of a wreck. The bottom of it has been bent over I assume to increase tire clearance but I didn't see anything to make me think it was something transferred on up to the door post. The door with the old hinges probably sagged a half inch so I was a little surprised. The hinges are all the same aren't they? I took some pics and uploaded them to photobucket, but they are down for site maintenance right now so I can't share them.
Also, the James Duff hinge set didn't come with door strap brackets and I can't seem to find them commercially available for lift off doors without buying the whole set. Are you uuys making your own? I was thinking of taking a 3/8th rod and heating it/beating it flat for about 2 inches and making a U for the strap part go on. Drill some mounting holes.
Photobucket is back up!
Last edited:











