• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Duff ride quality?

EB70

Sr. Member
Joined
Jun 9, 2006
Messages
730
I have a very traditional 70 with TBP 3.5" lift front and rear. It has dual shocks on the front and singles on the rear-they are older shocks, I don't know the valving etc. It is probably 2-3 years old and very low miles. Rides OK. I have a horribly rough rural driveway. I don't even think the leafs are broken in yet.

I just bought my new project Bronco and it has the entire James Duff kit front and rear, I think it is 2.5" but will need to measure as it may be the 3.5" kit.

Here is my question, compared to the TBP springs I am running, is the JD kit generally a little smoother riding? I am going to use it for sand, snow and a little crawling. My main concern is ride quality, with articulation in a crawler sense a distant concern.

I really like simple, and am the kind of guy what would run f-150 towers etc. just to keep things simple, but if the JD kit is that cool, I will cut the mounts off and move them over etc. and use all 8 shocks. I really want a smooth ride.

Thank you for your advise as always, really looking forward to digging into this build.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
offroad ride quality is more about tire pressure. get to 15 Psi or below is where its at. duffs 70/30 shocks do very well up front due to the rebound control of the coil springs. I have had dual shocks all around but have gone back to a single duff 70/30 up front ans single rancho 9000 in the rear. they are adjustable depending on the load you Carry.
 
OP
OP
E

EB70

Sr. Member
Joined
Jun 9, 2006
Messages
730
I'm pretty into airing down, however the pavement portion of any drive around here is a minimum of 40 miles round trip so I need to be moderate.

TBP is close enough I have bought parts after work there before. I like there stuff. What I don't know much about is Duff parts. I know they are very well respected and make good stuff. Mainly after a smooth ride and I own the new kit so I will install it regardless most likely.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
airing down is all about spending enough money for a good compressor. nobody minds airing up in 10 minutes but everyone hates airing up in 45 minutes or more.
 

spap

Bronco Guru
Joined
Jan 2, 2010
Messages
2,642
This just brought me back when I had a KBarS lift in my first bronco.
Talk about a wee bit stiff
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Which TBP springs and which shocks? Same 10 or 11 leaf rear packs, or the thinner more stock type?
Their own brand shocks, or someone else's?

One thing I think I'd do for sure is at least swap the shocks just to see if I liked one better than the other.
First I'd use one shock per wheel, then duals.

Just thinking that the shocks are easy to move around compared to springs (which aren't that bad, but still a lot more work goes into it) and that would at least give you one level of comparison to go on.

Paul
 

jim3326

Bronco Guru
Joined
Jul 12, 2010
Messages
1,781
Loc.
Appleturkey
This just brought me back when I had a KBarS lift in my first bronco.
Talk about a wee bit stiff

I had a superlift in mine, might as well had steel bars for shocks.

I believe the ride quality resides in the springs. I have the WH 3.5 progressives up front and 11 pack in back and mine rides better than my wife's Nagevader. The shocks will just complement the ride.

I get a boat load of articulation from the wristed axle and inboard mounted rear shocks. Depending on how you look at things, it's either a terrifying ride on the street or a whole lot of fun. I'm sure that depends on which side of the truck you're on!;D;D
 
OP
OP
E

EB70

Sr. Member
Joined
Jun 9, 2006
Messages
730
OK. It is definitely a 3.5" lift and has 70/30 written all over the shocks etc. The rear leafs are 9 leaf I think. It all came from Duff's. Other than being installed it has had very low use. Kind of excited to try it out and see how it works.

I am more worried about ride quality than a little quirky handling or body roll. I have been driving big tires on various crawlers for 30 years so I am sure it will be better than most. I think I am going to try it and just go from there. It isn't really practical to drive either right now as one is a project I am beginning, and the other is in storage mode.
 

PaveBronco

Sr. Member
Joined
Oct 30, 2012
Messages
914
I had a superlift in mine, might as well had steel bars for shocks.

Early 90's Ranch Single rate Coils and RS5000's......What were we thinking!

No need for dual shocks, and a lot depends on what you use your rig for and how your rig is built. Winch, bumpers, big tires, all make a huge difference.
I just went from WH to JD because I'm 90% road, I went with Bilstein, slightly firmer valving (winch up front) and RS9000's in the rear for the adjustability (should have just put them on the front also).Went with a front sway bar, the JD are 3 way progressive I think, and had a bit too much body roll....works great, no if I can only get my camber/caster numbers right....
 
OP
OP
E

EB70

Sr. Member
Joined
Jun 9, 2006
Messages
730
It will have 36-39" tires, winch etc. I am not a guy who throws 1/4" plate at every problem, but it will be heavier than stock. Generally, almost always in fact I like simple. One shock per corner, etc. But there must be a reason why they put two per corner. I am presuming it is to keep shock heat down, spread the load etc. and they must be valved for that use.

I have always been interested in the 9000 shocks. Do you PaveBronco believe they are worth the bucks? I do like the idea.
 
Top