• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Electric Engine Control (EEC)

Madgyver

Bronco Madman
Joined
Jul 30, 2001
Messages
15,030
Tell me what do I have...

It looks to be an 87 SD EEC.
 

Attachments

  • DSC01454.JPG
    DSC01454.JPG
    140.7 KB · Views: 32
Last edited:

SaddleUp

Bronco Guru
Joined
May 23, 2004
Messages
9,655
Loc.
Vancouver, WA
Yep. 87 SD for an Auto out of a Mustang. Or at least that's what the code (DE) shows up on Ryan's site as. The year comes from the Ford part number.

Not sure on the question so I'm going to guess. I assume you are wondering whether to run it or change it. That requires more questions though. For a stock motor with very little change the SD system is just fine. Once you start making changes to the motor (Especially things like a different cam) then either the SD system needs to be tuned using a chip (If it has a port for one which is doubtful in 87) or you need to switch to the MAF system. The difference is that the MAF system is better at coping with the changes and will learn a new program for them.

Actually I would go ahead and run that one for now. Swapping to the MAF one down the road isn't very complicated. The swap only takes a couple of hours and most of that is figuring out how to mount the MAF unit.
 
OP
OP
Madgyver

Madgyver

Bronco Madman
Joined
Jul 30, 2001
Messages
15,030
I notice there is a harness on both the passenger side and the driver side going in from the firewall.
I assume that the harness on the passenger side goes to the EEC but there is a couple of plugs that connect to the driver side harness.

Is this for the O2 sensors and the VSS?

Do I need to take the driver side harness also?
 

Attachments

  • DSC01455.JPG
    DSC01455.JPG
    150.3 KB · Views: 21
  • DSC01456.JPG
    DSC01456.JPG
    150.6 KB · Views: 22

SaddleUp

Bronco Guru
Joined
May 23, 2004
Messages
9,655
Loc.
Vancouver, WA
Madgyver said:
I notice there is a harness on both the passenger side and the driver side going in from the firewall.
I assume that the harness on the passenger side goes to the EEC but there is a couple of plugs that connect to the driver side harness.

Is this for the O2 sensors and the VSS?

Do I need to take the driver side harness also?
I don't think you need the drivers side stuff. Be sure you grab the one from the O2 sensors. It should plug in at the back of the engine though rather than the drivers side. For the 87 I suspect that the fuel pump portion is tangled into the main car harness so that will take a little to work out but just follow the diagrams and build a new harness for that part. You will need another relay for it but by the time you work through the rest that part will be easy. Be sure to add in the inertia switch to the main fuel pump power wire. It goes in series with it. I mention this because the diagrams don't show it in them. When you get done grabbing the harnes you should have 3 parts. The main injector part on the motor, the part that plugs into that and leads to the ECM, and the portion that goes to the O2 sensors (I believe it also has the VSS and tranny connector in that same one but I didn't use either on the last two I did so I'm not certain). Once you have the harness out take the Probst EFI book and trace the wires from the ECM pins to the end and mark what they go to. Your going to need to strip off the covering to do this. When I take the covering off I use wire ties to keep the harness together the way it was originally. Once you trace all of them out from the ECM it should identify the power and ground connections you need to make to the EB harness. Be sure you don't try to power the run connections from the coil wire though.(Been there done that) Either hook it up to another relay or run that clear to the ignition switch. (The latter is how I run mine)
 
Top