• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

FiTech/5.0 Explorer Install

68stang73

Sr. Member
Joined
Nov 29, 2015
Messages
399
I'm a few weeks out from ordering mine but I was thinking of modifying the drivers side air box to accommodate the command center. Those of you with this set up what's ur thoughts on that?
 

bteutsch

Sr. Member
Joined
Jan 11, 2009
Messages
875
I'm sure it's possible, are you thinking of putting it inside where the air box sits? If that's where you want it its your project.. I think you could make it work. I put mine on the radiator core support. It fit nice there...
 

68stang73

Sr. Member
Joined
Nov 29, 2015
Messages
399
Yeah it's just a thought right now. I like the idea of keeping it out of sight and in a cooler location from engine heat. Trying to hide as much fuel and electrical lines as possible. Figured I might need the extra space in the engine bay for some other goodies.
 

bteutsch

Sr. Member
Joined
Jan 11, 2009
Messages
875
I saw in a corvette forum where they used the charcoal canister location. That looked pretty cool I think it even fit the original bracket on the corvette.
 

bsquared

Contributor
Sr. Member
Joined
Dec 4, 2010
Messages
972
Got the 5.0 dropped in. Luckily I didnt have clearance issues with the serpentine brackets and the frame. I do however need to lower the PS reservior and mod the radiator brackets for the new reverse flow champion. Next I need to get the realys and harness done. Time is shorter than money right now, so it'll be a week or two before I get the harness started.

Got my FITech running last night! Still need to clean up and finish my fuel line, but it's good to go and seems to be running well.

Jim, I ran with the stock exploder PS pump for a couple of years and only really had power steering above 1500 rpms. I know that pump can be rebuilt into a F350 pump, but I just went with the WH conversion bracket and Saginaw pump. Now have power steering like a new car. Just FYI, as your mileage may vary.

Good luck with your build and give me a shout if I can help. Cheers, B2
 
OP
OP
jimschulz

jimschulz

Full Member
Joined
Sep 6, 2013
Messages
215
Loc.
Eastern Washington
Alot of progress this weekend. Got the new pilot bushing and the 5.0 is in and buttoned up. Got the harness done and tested. need to install harness and new fuel lines and pumps. I did decide to go with a relay off the ignition switch. Hope to get the fuel pumps in next weekend.
 

Attachments

  • IMG_0477.jpg
    IMG_0477.jpg
    93.5 KB · Views: 108
  • IMG_0478.jpg
    IMG_0478.jpg
    132.4 KB · Views: 115
OP
OP
jimschulz

jimschulz

Full Member
Joined
Sep 6, 2013
Messages
215
Loc.
Eastern Washington
Well, I got the 5.0 fired up last night. Had a few issues initially getting it started, but that was because I failed to realize the 94 and up 5.0's went to the HO/351 firing order. But after getting that straight and resetting the learn, It fired right up and runs great. My relay off the 904 wire is working great with no issues yet. The Carter HP4600 is a Noisy pump! I'm not pleased with that, but can look for someting else later. Was able to drive around a little today and the system seems to be learning pretty well. The only thing I dont like so far is the slight backfires on deceleration. This may subside the more I drive it, but time will tell. Overall I am pleased with the FiTech, it starts right up and is doing what its supposed to as far as idle and fan control goes. Will put some miles on it this weekend and see how things go.
 

bteutsch

Sr. Member
Joined
Jan 11, 2009
Messages
875
Probably I was running about 12 and getting backfire on decel. It won't hurt to try. I'm either at 8 or 10 now. It's not doing it anymore. No noticeable change in performance.
 

bsquared

Contributor
Sr. Member
Joined
Dec 4, 2010
Messages
972
You guys rock! I am also hearing just a little bit of backfire on deaccel and might dial my timing back a bit and see what happens.

Are y'al resetting the "learning" curves when you do something like change the timing? Seems like I should.

Thanks, B2
 
OP
OP
jimschulz

jimschulz

Full Member
Joined
Sep 6, 2013
Messages
215
Loc.
Eastern Washington
I set my timing with a vaccum guage today and then reset the learn. The thing runs like a raped ape! No backfire and very, very responsive. The timing shows something like 30 initial now, So I dont think my HB is marked correctly. Im going to find my TDC with plug indicators and see where I'm at. The only thing Ive noticed after setting the timing using vaccum is that I cant get it to idle below 900. I also think the ECU tries to control timing even after the 2K RPM suggested by fitech. Its a work in progress. When you change the learn to 1, you have to turn the key off to get it to clear. Just an FYI.
 

m_m70

Contributor
Bronco Guru
Joined
Jun 14, 2001
Messages
1,770
Loc.
Prescott AZ
Jim, do you have the fitech controling the timing? Since I changed over to fitech controlling the timing it has ran a bit flat and backfires on decel. Curious, when you changed your timing with a vacuum gauge did you change the base settings or was it still synced up with the ecu? Mines reading around 20* btc now and backfires pretty good on decel even just goosing it in the driveway.
Thanks!
 
OP
OP
jimschulz

jimschulz

Full Member
Joined
Sep 6, 2013
Messages
215
Loc.
Eastern Washington
m_m70, Yes I have the FiTech controlling the timing. Running an MSD 2 wire dizzy locked out. I left the base timing in the ECU at 12, but set the dizzy to highest vaccum at idle. What a difference! before doing this, I too was running very flat (Gutless) and decel backfires with an occasional TBI backfire. Now the throttle response is crisp and there is no backfire on decel. My only problem is the high idle and I dont know if I should change the base in the ECU? I can live with a 900 RPM idle though. I think I'm going to run for a few days and see how the learn goes. I will follow up with results. One other note is now when I turn the key it starts in about a half a second, whereas before it would crank a couple of times.
 

68stang73

Sr. Member
Joined
Nov 29, 2015
Messages
399
I'm sure setting the control unit to desired rpm will help. If not mayb closing if throttle blades a tad should do the trick.
 
OP
OP
jimschulz

jimschulz

Full Member
Joined
Sep 6, 2013
Messages
215
Loc.
Eastern Washington
Did some more driving and seems to be running well. I did find a split in my brake booster line and when I fixed that it will idle down now to 770 RPM.... Still don't know if I should change my initial in the ECU as everything seems to be working great.
 

68stang73

Sr. Member
Joined
Nov 29, 2015
Messages
399
Yeah I was thinking about that. You might want to see where your total is now. I hope it's not above 40-50. Should be somewhere around 34-36 total. Throw a light in it and bring up the rpms and check it.
 
OP
OP
jimschulz

jimschulz

Full Member
Joined
Sep 6, 2013
Messages
215
Loc.
Eastern Washington
Just checked the timing and its around 33-34 total timing. It is running great. No backfires and plenty of power. Im going to run it for a while and break it in a little.
 
Top