• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Fuel injector size ??

screamin reel

Sr. Member
Joined
Nov 18, 2005
Messages
664
Loc.
Calgary, Alberta, Ca
Can't seem to find my answer in the search.
My plan is to get an F150 / 5.0 SD (donor) which is 185 hp vs. the 5.0 car SD which is 150 - 160hp. I think the trucks came with 17lb injectors. Replacements I have read come up to 24lbs for the F150 / 5.0's.
By changing out the intakes to that of a car 5.0 with 14lb injectors, is that going to screw me up ?
Can I replace the 14lb car injectors with the 17lb - 24lb truck injectors if i'm using all the Speed density stuff off of the donor truck ?
I know most will say go mass air but i'm looking at this as a simple swap without having to convert everything to mass air.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
I would not expect it to work very good.

Typically, non-HO cars were 14s
HO and truck were 19s
Late Explorer were 17
460 and Cobra were 24.
 
OP
OP
screamin reel

screamin reel

Sr. Member
Joined
Nov 18, 2005
Messages
664
Loc.
Calgary, Alberta, Ca
So if I understand this correctly, if I choose to go the F150 route as a donor, I would also have to swap intakes from an Explorer, or HO Mustang, t-bird or Cougar to be able to use the 17 - 19lb injectors correct ?

I have seen a few 5.0 HO's in the boneyard over the last few months if those are the intakes I need. I have only seen one H.O advertised in the last 4 months here that could be used as a donor.


I guess the reason for the F150 5.0 is the hp difference between the truck 185hp and car 150hp 5.0. Also hoping on the 4x4 aod to make things simpler.
 

A&Mbronco

Sr. Member
Joined
Nov 18, 2004
Messages
547
Loc.
Houston,TX
The injectors will fit any of the intake. You will want to get a different intake though, truck intakes are way too tall.
 

nephic2

New Member
Joined
Jan 23, 2006
Messages
32
Loc.
Buffalo, Wyoming
To the origional question, yes go ahead and use the car intake, but you need to make sure your injectors match what the computer is from, therefore if teh computer thinks 19 lbs. injectors, those need to be on the lower intake...and after you get all the plumbing and witing woes figured out, switching to mass air later to run your stroked 351 will be fairly easy.
 

needabronco

Bronco Guru
Joined
Jul 2, 2004
Messages
6,411
Loc.
Prescott/Farmington
You need to make sure the MAF, the injectors, and the computer match. Most important is the MAF and the injectors. If the MAF is for 14 lb injectors with 19lb injectors, you will burn too much fuel, confusing the sensors and the computer resulting in a poorly running engine.

Find a 96 Explorer MAF I bought one on ebay for $20, it will work for 19 lb injectors.
 

minimatt

Full Member
Joined
Jun 3, 2005
Messages
173
The short, easy answer is: Take the donor truck injectors and put them into the car intake. Use everything else from the donor truck.

The long answer is: Get a donor with mass-air and sequential fuel injection instead of the bank fire speed-density stuff you are looking at. More power, better drivability and better fuel economy being the biggest advantages. I believe '95-96 F-150's had this set-up and of course the 88-95 50-state Mustangs or 89-95 federal Mustangs, as well as various other Ford-Lincoln-Mercury vehicles.
 

minimatt

Full Member
Joined
Jun 3, 2005
Messages
173
If I sold Aimee's Bronco, she'd likely braid my nuts. We're all doin' fine. I'm starting to build a trailer for the new boat this weekend. That will be the new family recreation vehicle/hotrod. The boat is to be completed the end of May and is entered in a show June 2, so I better get with the program on the trailer. I'll send you some pic's with it all hooked to the back of the Bronco.

Tell the family we said hello.
 
OP
OP
screamin reel

screamin reel

Sr. Member
Joined
Nov 18, 2005
Messages
664
Loc.
Calgary, Alberta, Ca
Forgot to say Aimee's Bronco. Oops !
Looking forward to the pics. I'd love to do an old Chris Craft. I'm sure that would send the wife into a tail spin.
Just a little different from what you have on your plate but this was the fly fishing pram I built 2 years ago.
Good luck with it.
Bruce
 

Attachments

  • 0101.JPG
    0101.JPG
    56.2 KB · Views: 71

minimatt

Full Member
Joined
Jun 3, 2005
Messages
173
That is a sweet little boat. I've got a thing for wood boats, too. We have the woods selected for our boat and the deck is currently under construction. It will be a glass hull with a quilted maple deck and figured cherry hardwood trim. We will wait until the deck is complete to pick paint colors. 509" Chevrolet, Turbo 400, V-drive for drivetrain. More for trolling than fly fishing....
 
OP
OP
screamin reel

screamin reel

Sr. Member
Joined
Nov 18, 2005
Messages
664
Loc.
Calgary, Alberta, Ca
The 87 - 88 Mustangs were 225hp. Other years were 200 - 210 stock unless it was a cobra.
150 hp are the crown Vics, Marquis etc.
F150 5.0 - 185 hp
5.8 - 210 hp
 
OP
OP
screamin reel

screamin reel

Sr. Member
Joined
Nov 18, 2005
Messages
664
Loc.
Calgary, Alberta, Ca
Info from the Mustang site.

1986 200 hp @ 4000 rpm 285 ft-lb @ 3000 rpm
1987-1988 225 hp @ 4000 rpm 285 ft-lb @ 3000 rpm
1989-1993 205 hp @ 4200 rpm 300 ft-lb @ 3200 rpm / 93 was 280 @ 3400
1993 cobra 245 hp @ 5000 rpm 290 ft-lb @ 4000 rpm
1994-1995 215 hp @ 4200 rpm 285 ft-lb @ 3400 rpm
 
Top