• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Fuel Injectors?

WyleCoyote

Bronco Guru
Joined
May 2, 2002
Messages
1,739
Ok, so I have the Lincoln 5.0...Injectors are all questionable...

I need to replace them, so should I go with the 15lb injectors that were stock, or should I go with 19lb injectors? will it screw up the computer if I go to the 19lb injectors? It is MAF.

believe it or not, the 19lb injectors are cheaper and easier to find.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,115
Injectors must match what the computer is programmed for. What computer are you going to be running?
 
OP
OP
WyleCoyote

WyleCoyote

Bronco Guru
Joined
May 2, 2002
Messages
1,739
I have the computer that came with the car, it's not one of the normal ones mentioned on here. I'll have to get the digits off it later.
 
OP
OP
WyleCoyote

WyleCoyote

Bronco Guru
Joined
May 2, 2002
Messages
1,739
Darn. Ok, looks like that is the route I'll go. Anyone have a line on the best(Cheapest) place to get new injectors?
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
Darn. Ok, looks like that is the route I'll go. Anyone have a line on the best(Cheapest) place to get new injectors?

Might be cheaper to send your to Mr. injector to get them cleaned and tested.

I get them from the junkyard.
 
OP
OP
WyleCoyote

WyleCoyote

Bronco Guru
Joined
May 2, 2002
Messages
1,739
Can they fix the one that broke when I pulled it from the manifold?
 
OP
OP
WyleCoyote

WyleCoyote

Bronco Guru
Joined
May 2, 2002
Messages
1,739
Cool, thanks guys, I broke the nose piece that sticks into the manifold. I was stuck in there, had to chip the plastic part out. I did find a full set on Ebay for $86, I might go that route.
 

eds66bronco

Bronco Guru
Joined
Aug 3, 2004
Messages
1,119
Loc.
Essex, Vermont
I used this guy... http://www.witchhunter.com/
way cheaper than buying new. He got all mine to flow better than factory spec., had quick turnaround too. I'd just grab a replacement at the junk yard and send them off to be cleaned. you may find the e-bay set has a stuck injector and then you'd still be in the same boat.
 
OP
OP
WyleCoyote

WyleCoyote

Bronco Guru
Joined
May 2, 2002
Messages
1,739
You know what is cool about that, I'm close by to Bothell, WA! Figures it would take a Bronco Brother in Vermont to find me a local shop..
 

msweb

Bronco Guru
Joined
Aug 29, 2003
Messages
2,377
Old thread so hopefully not a hijack... Since it was recommended that they were sent off to be cleaned, is there not a way one could do it themselves? Only reason I ask is because I was trying to figure out how to clean mine before putting everything back together...
 

Randrew

Jr. Member
Joined
Dec 2, 2006
Messages
50
Loc.
Tempe, AZ
Old thread so hopefully not a hijack... Since it was recommended that they were sent off to be cleaned, is there not a way one could do it themselves? Only reason I ask is because I was trying to figure out how to clean mine before putting everything back together...

I haven't done it personally, but a buddy of mine bought the rebuild stuff from rjminjectiontech.com and followed this writeup. I don't think he used an ultrasonic cleaner. Maybe he just soaked them instead. Either way, he said it worked out fine. There's also a brief writeup here. You might also buy an injector pigtail so you can make a test harness to open up the injector.
 

msweb

Bronco Guru
Joined
Aug 29, 2003
Messages
2,377
I haven't done it personally, but a buddy of mine bought the rebuild stuff from rjminjectiontech.com and followed this writeup. I don't think he used an ultrasonic cleaner. Maybe he just soaked them instead. Either way, he said it worked out fine. There's also a brief writeup here. You might also buy an injector pigtail so you can make a test harness to open up the injector.

Wow, so much for using compressed air and a bottle brush but then again, it isn't a jet from a Holley, is it! Thanks for the links!
 

HoosierDaddy

Contributor
Bronco Guru
Joined
May 29, 2006
Messages
2,776
I cleaned mine using the RJM instructions , kinda , my soak lasted a long time till I could get back to finish them.
No problems so far .... luckily I had the old chopped harness and had all 8 pigtails. Only one is needed .....

If I have extras , I could mail you one .....
 

msweb

Bronco Guru
Joined
Aug 29, 2003
Messages
2,377
I cleaned mine using the RJM instructions , kinda , my soak lasted a long time till I could get back to finish them.
No problems so far .... luckily I had the old chopped harness and had all 8 pigtails. Only one is needed .....

If I have extras , I could mail you one .....

What did you soak them in? I actually have 2 sets of 19lb injectors and harnesses to use but I do appreciate the offer!

I built my own tester / cleaner.

I saw that, pretty impressive but way over my head. If I decide to go ahead and clean/rebuild them I'm hoping this will be a one time shot. I may just soak them and go from there, I dunno yet. I'm working around Anthony's schedule here and I don't want to be in the middle of something when he needs it for the next step.

I do like the idea of rebuilding them if nothing else for the challenge. The EFI swap that scared me earlier is becoming something that I'm picking up faster than I thought and I'm actually enjoying learning about it! ;D
 
Top