• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Gearing?

bigjhoov

nobody
Joined
Apr 10, 2005
Messages
3,583
I need some new gears. Problem is, I can't decide how deep to go. I run a 200 inline six with 35's and 4.11's. Needless to say , it's lacking in bottom end. I've found a gear ratio calculator that say's 5.13's are the way to go. What do ya'll think about this. I want more bottom end, but don't want to lose the ability to jump on the highway if needed.

http://www.dirtroadmagazine.com/gears.htm
 
Last edited:

Doyle

Bronco Guru
Joined
Jun 12, 2006
Messages
1,026
2708 at just 55, interstate at 70 is 3447, if tranny final ratio is 1:1.
 
OP
OP
bigjhoov

bigjhoov

nobody
Joined
Apr 10, 2005
Messages
3,583
Why do you say that? 4.88's are originally what I was considering. I don't want to do this twice.
 

rednck21

Bronco Guru
Joined
Feb 27, 2002
Messages
3,915
i wouldnt want anything screaming on the interstate...even if it was a 6cyl.

on the orange 77, i went with 4.10's and 33's because it was "close" to stock...wrong, it was terrible on the intersate. it would have been perfect with an OD trans though.

im leaving the 4.10's in pat's old rig with the 35's and it should be just about right:cool:
 

Tito

CB Fire Starter
Joined
Jan 29, 2006
Messages
10,781
Loc.
Bakersfield, CA
I think the 4.88s would be good, freeway speeds are a LOT faster than back in the 60's and 70's and if you clock much daily driving time then a little sacrifice in low gearing would be worth the niceties on the street. I've got 5.13's with my 37's and I am about maxed @ 60 really for any distance. I however dont plan to put this on the hiway, just town cruising and off road. When I go to 39.5's I'll have a different problem on the hiway ;D
 

rednck21

Bronco Guru
Joined
Feb 27, 2002
Messages
3,915
yeah. up to about 55 was ok, but any faster than that just made me cringe:(
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
4.88's might be a good in between choice.
Keep in mind that broncos were built when the speed limit was 55mph so the gearing and engine was setup for that speed from the factory. If you plan on hiway driving with low gears you should have a camshaft that is matched to the RPM's you will be running but usually the slightly less than optimum gearing will create a slight OD effect its just that some engines dont have the power to maintain speed without the gearing. So the lower gears will get your lowend back and will allow you to maintain speed on the hills.
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
Well is it possible to figure out what size tire will make up the difference. That way you could put that tire on and go see what 5.13 would run out to. Same with the 4.88. What I mean is if the 4.11 and 35'' tire combo at 60 = ?rpm. Then what size tire would it take to make the same 4.11 gear seem like the proposed 4.88 or 5.13? Someone needs to do the math and then find out what dia tire is needed to do the test. This way you could figure out if you liked it or not. There was a chart on this site that had a bunch of final drive rpm's for gear and tires used.
Does an of this make sense?
65mph with 35'' tires and 4.88 = 3100 rpm
5.13 = 3300 rpm
I would go with the 5.13 what's the big deal over 200 rpm's That 6 is though as nails and would run that rpm all day.
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
Big question is what rpm are you OK with? Then do it.
 

bludorbronc

Sr. Member
Joined
Apr 19, 2006
Messages
653
Figure out at what rpm you want to run at on the highway and install that gear. Then to run the trails install a doubler to get trail gearing. Best of both worlds.
 

Gummi Bear

Bronco Guru
Joined
Jul 8, 2003
Messages
3,647
Jer - I don't think you can go wrong with 4.88 or 5.13, there's not a whole truckload of difference between the two, and they'll both be a dramatic improvement over what you've got now.

Truth be told - for overall driveability, I'd go with the 4.88's. If you're planning for it to be more of a trail machine, go for the 5.13's.

If the decision becomes too much, just toss out everything, and put in some Rocks with 6.72, and forget being conventional. ;D
 
Top