Koenig winch parts

[mainsail09]

Anyone know where to get parts for these. I was informed by RKI they are obsolete and they had nothing. I googled but turned up some very old posts.
I need gaskets and drum bushings.

 

[bmc69]

Broncitis (Drew) on here has quite a few parts for those. He'll certainly chime in at some point or you could PM him.

 

[Broncitis]

Let me know which part numbers you need and I will get some prices together.

 

[PaveBronco]

Anyone got a Vendor part number for the seal 40012...appart from 40012 number. Mine is leaking bad. I suppose I could pull it and try to get the part number.

 

[Broncitis]

I do not have a cross reference for standard seal numbers for these.

 

[CopperRanger]

Anyone got a Vendor part number for the seal 40012...appart from 40012 number. Mine is leaking bad. I suppose I could pull it and try to get the part number.

I replaced my seal last year, when I pulled it there were no numbers on it. I did get a TIMKEN 471570 .875x1.499x.250 was the size on the box. Not sure if it is the exact one, the OD was spot on, but the ID could have been a little tighter in my opinion, It still dripped a little. Before I reinstall it on the Bronco I am going to look again for a tighter one.

 

[mainsail09]

Its a CR8748

 

[mainsail09]

Drew, Is 41266 the notched spacer that fits around the 2 keys in the drum shaft? If so I need it and:
40005
42587
42445
42444
Thanks

 

[CopperRanger]

Its a CR8748

Is this the oil seal for the shaft on the winch? Also what brand is that?

 

[71 Red Bronco]

Koenig King Winch Parts

I too was told by RKI that they no longer make parts for these old winches. Lucky for me I found a good dealer for RKI that determined otherwise. I had an original parts list for my winch. When I sent it to him we determined that it was almost a perfect match with a current RKI parts list. Even to the point where 99% of the original part numbers were the same. I ordered what I needed and rebuilt my winch. All the parts I ordered fit and my 43 year old winch works like new. The parts are not cheap but they are available.

 

[thegreatjustino]

Who is the dealer? Your post is just a tease without contact info...

 

[buck68]

When I needed parts for mine, I went online to an RKI site and they gave me 3 dealers within ten miles of my home. They had no problem getting what I needed. Very expensive and a couple of the gaskets had holes that didn't quite line up. However, the seal that went around the shaft fit perfect. Snug, absolutely no leaks.

 

[mainsail09]

The seal is a CR, Chicago Rawhide. I found one at a local mill supply house. I think the dimensions are .875 X 1.5

 

[PaveBronco]

Who is the dealer? Your post is just a tease without contact info...

X2..Im sitting on pins and needles here....where's the info....

 

[71 Red Bronco]

The Koenig winch on my Bronco was installed new in 1971. It's a king model 100. It matches the current RKI model 08 MLX-SS parts list and diagram. http://www.rki-us.com/productDetails.aspx?cat=5&type=16&series=18&prod=08MLX# Some parts were slightly different than the original but functioned and fit correctly. I assume they are engineering upgrades. I went on the RKI website and found a nearby dealer. The one I dealt with is located in Marshfield WI but shipped directly to my address. Their prices were about 40% less than the RKI list price for each part. If you want the dealer contact info send me a PM.