• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Larger R&P/Diff Not Fitting in Case

Ol'Blue

Contributor
Bronco Guru
Joined
May 28, 2013
Messages
1,982
I currently have a '77 Ford 9" Rear with open diff, 28 spline and 3.50 gears. I ordered 31 spline Yukon Trac Loc and 4.30 R & P.

I sent the third member out to be set up and they guy is telling me that everything is too large. The ring gear and carrier are too large to fit in the drop out.

He said grinding would pretty much put a hole in the case.

Any other solutions or do I need a larger case/drop out made for the larger ring gear?

Argh!
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
That's not uncommon to have to do a bit of grinding on some cases. Over 4.10 seems to be where they get close. I bought a Strange nodular case when I did mine. It's quite the investment to build a complete rear chunk. The stock cases have been known to break. Air down those 35's, low range and running 4.30 gears, it puts a huge amount of stress on that case. It's just cheap insurance to upgrade to the nodular case. IMO.

Mark
 

broncodriver99

Bronco Guru
Joined
Jan 27, 2008
Messages
4,780
Loc.
Glen Allen, VA
I had a similar problem when I went to 4.11. It seems Ford clearanced the cases differently for the larger gear sets. I had to take material off of the pinion support bearing area of the case and also had to make room for the ring gear bolts on the inside of the case. I have a case for another 9" that has factory 4.11 and there is definitely a difference in how it was ground/clearanced inside. Unless you have an oddball 8-3/4' case or something weird there should be enough material to make room.
 

welndmn

Bronco Guru
Joined
Nov 12, 2001
Messages
2,112
Has this shop ever setup a ford 9" before?
If It were me, I'd just tell him thank you and grab my parts and leave.
Every ford 9" center has to be ground on the pinion bearing support once you go over a 4:10 gear.
 
OP
OP
Ol'Blue

Ol'Blue

Contributor
Bronco Guru
Joined
May 28, 2013
Messages
1,982
That's not uncommon to have to do a bit of grinding on some cases. Over 4.10 seems to be where they get close. I bought a Strange nodular case when I did mine. It's quite the investment to build a complete rear chunk. The stock cases have been known to break. Air down those 35's, low range and running 4.30 gears, it puts a huge amount of stress on that case. It's just cheap insurance to upgrade to the nodular case. IMO.

Mark

Thanks Mark, any good source for a nodular at a good price?
 
OP
OP
Ol'Blue

Ol'Blue

Contributor
Bronco Guru
Joined
May 28, 2013
Messages
1,982
Has this shop ever setup a ford 9" before?
If It were me, I'd just tell him thank you and grab my parts and leave.
Every ford 9" center has to be ground on the pinion bearing support once you go over a 4:10 gear.

He mostly does Heeps but has done 9s before (some for our members). Has had to grind in the past but says this one need so much that he is concerned of having enough material and weakening the case.
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
Every ford 9" center has to be ground on the pinion bearing support once you go over a 4:10 gear.
I put 4.56 gears in my 9", which I believe is the stock 1970 Bronco case, and didn't have to do any grinding.
 
OP
OP
Ol'Blue

Ol'Blue

Contributor
Bronco Guru
Joined
May 28, 2013
Messages
1,982
Thanks Mark, any good source for a nodular at a good price?

Nevermind Mark, I went ahead and took your advice and ordered a nodular case. A couple hundred bucks is worth the piece of mind, just need to convince the wife of that when I get home.

Thanks for the help all!
 
OP
OP
Ol'Blue

Ol'Blue

Contributor
Bronco Guru
Joined
May 28, 2013
Messages
1,982
Yep I got the Yukon. Hope it's a tough one.

Time to start saving for the front!
 

spap

Bronco Guru
Joined
Jan 2, 2010
Messages
2,642
Hey Ol'blue where are you getting the work done is he a local orange county guy. That's my next step is the rear end but I need to fit 4.86s in my 77 thanks
 
OP
OP
Ol'Blue

Ol'Blue

Contributor
Bronco Guru
Joined
May 28, 2013
Messages
1,982
Hey Ol'blue where are you getting the work done is he a local orange county guy. That's my next step is the rear end but I need to fit 4.86s in my 77 thanks

Yo SPAP,

Sure hes in Yorba Linda and was referred to me by another member here.

Robert Kobal
www.RWKHausSupply.com
714-875-2414

Good luck,
 

Sabas

Sr. Member
Joined
Jun 24, 2003
Messages
658
Robert set up my gears & lockers for my Dana 44. Top notch, he has done regearing for a few Broncos guys and is active in off road raving and ultra 4. I went to a modular 9 when I did 4.56 gears.

Sabas
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,553
I buy the "strange" gear cases. I have had real good luck with them.
 
Top