• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Low Fuel Pressure...found problem??

zion2004

New Member
Joined
Nov 3, 2007
Messages
18
Guys,

I posted a couple times about a hard starting situation with my 73 bronco
to recap: Nicely bulit 302, with edelbrock cam, manifold and carb setup
approximately 5000 miles on engine...runs great. The problem is that it fires right up when it's cold....like today 45deg.....but as it warms up to operating temperature...sitting and idling or driving around town....once you shut it off
and go in the store or whatever it is very hard to start. I have a line gage
and the fuel pressure drops over a period of time from 5psi to 0 while it's running...it has never stalled on me. So here's what i have done: replaced
the line gage to verify pressure reading. Replaced the fuel pump, replaced all
the rubber fuel line from pump back, replaced both small line filter and my
big fram cartridge filter, left the gas caps off while running, isolated the hard
line from pump to carb so no heat was transmitted, and finally running a rubber line into a 5 gallon gas can right into the pump.....i did this last thing
yesterday to see if i could at least peg down the problem area. It fired right up and then again slowly began to lose fuel pressure...i shut it off when it had
3 lbs and then started it right up again....no problem....after 20 minutes the fuel pressure was at 0 on the gage. I shut it off and had the intentions of taking the top of the carb off to see how much fuel was in the bowls...as i
was face to face with the carb....and the truck had been off about 2 minutes
i saw gas starting to drip out of the little brass things on the primary venturi
booster (i'm not a carb guy...i think this is what they are after looking on the
edelbrock exploded view website) at first it was just a drop or two...and then it was a decent amout of gas getting dumped down the carb! So i'm thinking
i found the problem...that much gas would almost make it seem like it was flooded right....and taking alot of craking to start?? So today i wanted to verify that this what was going on.....and yes it did it again...this time i had my head right near the carb....and as it started to drip gas ....i think i heard
what sounded like boiling?? Is this the reason the fuel is leaking into the carb?
I had felt the carb before and it was not unpleasent to touch? The temp gage on the truck read about 190-210 (stock bronco gage) What should i do to fix this thing.....I don't know much about carbs.....or the boiling point of
todays gas. Any help or suggestions would be appreciated.

Thanks in advance!
Steve T.
 

scsm76

Bronco Guru
Joined
Oct 6, 2005
Messages
1,433
Loc.
Shaver Lake, CA
The float may be set to high and it is just overfilling the bowl or the needle or seat is bad. The edelbrock carbs are real easy to take the top off and check on the truck. If you can touch the carb I doubt the fuel is boiling in it, your most likely hearing the coolant somewhere in the engine.
 

COBlu77

Sr. Member
Joined
Feb 10, 2004
Messages
867
Loc.
Arvada, CO
When I ran a carb I had the same problem. I thought it was vapor locking, but what was really happening was that the aluminum manifold was transferring too much heat and the gas was literally boiling out of the carb. It was worse at high altitude. A 1/2" phenolic carb spacer from Summit solved my problem.
 

mr incredible

Bronco Guru
Joined
Feb 25, 2007
Messages
2,217
sounds to me like the needle seat is bad . i had the same thing happen to my carb one time , it would build line pressure , and evacuate it to the venturies , in my case , it was the needles and seats ,,,your case might be different , but i would check them .
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Dito the spacer there are also 1/4 thick gaskets availible that really help isolate the heat. I'd also consider gettimg the guage checked maybe try a mechanical gauge to ensure you have a true reading. If its reading 210 then I would cnsider getting the radiator cored or a new radiator to restore your cooling system.
 
Top