Guys,
I posted a couple times about a hard starting situation with my 73 bronco
to recap: Nicely bulit 302, with edelbrock cam, manifold and carb setup
approximately 5000 miles on engine...runs great. The problem is that it fires right up when it's cold....like today 45deg.....but as it warms up to operating temperature...sitting and idling or driving around town....once you shut it off
and go in the store or whatever it is very hard to start. I have a line gage
and the fuel pressure drops over a period of time from 5psi to 0 while it's running...it has never stalled on me. So here's what i have done: replaced
the line gage to verify pressure reading. Replaced the fuel pump, replaced all
the rubber fuel line from pump back, replaced both small line filter and my
big fram cartridge filter, left the gas caps off while running, isolated the hard
line from pump to carb so no heat was transmitted, and finally running a rubber line into a 5 gallon gas can right into the pump.....i did this last thing
yesterday to see if i could at least peg down the problem area. It fired right up and then again slowly began to lose fuel pressure...i shut it off when it had
3 lbs and then started it right up again....no problem....after 20 minutes the fuel pressure was at 0 on the gage. I shut it off and had the intentions of taking the top of the carb off to see how much fuel was in the bowls...as i
was face to face with the carb....and the truck had been off about 2 minutes
i saw gas starting to drip out of the little brass things on the primary venturi
booster (i'm not a carb guy...i think this is what they are after looking on the
edelbrock exploded view website) at first it was just a drop or two...and then it was a decent amout of gas getting dumped down the carb! So i'm thinking
i found the problem...that much gas would almost make it seem like it was flooded right....and taking alot of craking to start?? So today i wanted to verify that this what was going on.....and yes it did it again...this time i had my head right near the carb....and as it started to drip gas ....i think i heard
what sounded like boiling?? Is this the reason the fuel is leaking into the carb?
I had felt the carb before and it was not unpleasent to touch? The temp gage on the truck read about 190-210 (stock bronco gage) What should i do to fix this thing.....I don't know much about carbs.....or the boiling point of
todays gas. Any help or suggestions would be appreciated.
Thanks in advance!
Steve T.
I posted a couple times about a hard starting situation with my 73 bronco
to recap: Nicely bulit 302, with edelbrock cam, manifold and carb setup
approximately 5000 miles on engine...runs great. The problem is that it fires right up when it's cold....like today 45deg.....but as it warms up to operating temperature...sitting and idling or driving around town....once you shut it off
and go in the store or whatever it is very hard to start. I have a line gage
and the fuel pressure drops over a period of time from 5psi to 0 while it's running...it has never stalled on me. So here's what i have done: replaced
the line gage to verify pressure reading. Replaced the fuel pump, replaced all
the rubber fuel line from pump back, replaced both small line filter and my
big fram cartridge filter, left the gas caps off while running, isolated the hard
line from pump to carb so no heat was transmitted, and finally running a rubber line into a 5 gallon gas can right into the pump.....i did this last thing
yesterday to see if i could at least peg down the problem area. It fired right up and then again slowly began to lose fuel pressure...i shut it off when it had
3 lbs and then started it right up again....no problem....after 20 minutes the fuel pressure was at 0 on the gage. I shut it off and had the intentions of taking the top of the carb off to see how much fuel was in the bowls...as i
was face to face with the carb....and the truck had been off about 2 minutes
i saw gas starting to drip out of the little brass things on the primary venturi
booster (i'm not a carb guy...i think this is what they are after looking on the
edelbrock exploded view website) at first it was just a drop or two...and then it was a decent amout of gas getting dumped down the carb! So i'm thinking
i found the problem...that much gas would almost make it seem like it was flooded right....and taking alot of craking to start?? So today i wanted to verify that this what was going on.....and yes it did it again...this time i had my head right near the carb....and as it started to drip gas ....i think i heard
what sounded like boiling?? Is this the reason the fuel is leaking into the carb?
I had felt the carb before and it was not unpleasent to touch? The temp gage on the truck read about 190-210 (stock bronco gage) What should i do to fix this thing.....I don't know much about carbs.....or the boiling point of
todays gas. Any help or suggestions would be appreciated.
Thanks in advance!
Steve T.











