• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

LOWERING my Bronco

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
In some of the old street rods model t's? They don't run a top and I believe they chop the windshield. Looks pretty cool... Having a small low windshield topless.
 

chrlsful

Bronco Guru
Joined
Oct 21, 2009
Messages
1,448
In some of the old street rods model t's? They don't run a top and I believe they chop the windshield. Looks pretty cool... Having a small low windshield topless.

Like I said earlier, "surry w/da fringe on top".
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
Just driving it around a bit while figuring out the next step with the rear suspension. Shopping shocks and or coil overs.

I am also looking to make a windbrake like on the bmw convertables.
 

chrlsful

Bronco Guru
Joined
Oct 21, 2009
Messages
1,448
slammed bronk

Just driving it around a bit while figuring out the next step with the rear suspension. Shopping shocks and or coil overs.
I am also looking to make a windbrake like on the bmw convertables.

Love 2 C some pic (all ways) esp of results of removing the 4 - 6 inch rise under the driver's seat (if U DID mod there as written earlier). :eek: How bracin wuz done, how blended w/tunnel, etc.

Thanks, enjoy yer new ride!
 

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
Love 2 C some pic (all ways) esp of results of removing the 4 - 6 inch rise under the driver's seat (if U DID mod there as written earlier). :eek: How bracin wuz done, how blended w/tunnel, etc.

Thanks, enjoy yer new ride!

It will be a bit before I get to that but you will definitely see those pics in the future. My chop is going to be a bit more radical that what we have seen so far.
I will be removing the drivers side step as well as moving both sides further back.
 

chrlsful

Bronco Guru
Joined
Oct 21, 2009
Messages
1,448
will be removing the drivers side step as well as moving both sides further
back.

"B 4 I get 2 that"
No comprende`. Thought it wuz 'on the road'.
Anyway, it would B of benefit to me to see how U did/do the lowering-of-the-drivers-seat or (I assume yer nomenclature) step (plus custom up the bracing/tunnel from the oe) that U wrote bout earlier. Is that still in the cards/done?

Not sure what U mean bout "moving both sides back" unless U mean length the cab area for longer legged drivers/passengers. The 2 - "down and back" would B an exact goal I'd pursue to "modernize" the driver positioning (pages ago I wrote bout the '79 bronk tilt wheel I wish to install along with these 2 changes).

Thanks -
Cordially,
Another Interested Owner/Reader
 

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
I have a similar project going on in another thread..."Streetrod Bronco"
Greatguy and Behemoth has this thread running. I am a subscriber here... since they have gone through it and there is plenty of experience and "lessons learned".

Yes down and back... that part is not completed yet. Although I did raise the rear bed floor up a few inches so that I can drop the truck lower. I plan on running both floor pans to the step for the bed. My reason... I am planning for a more radical chop and will need head room. I am doing a prostreet type Bronco...

Goal for summer is suspension so I can move it in and out of garage ;)
 

chrlsful

Bronco Guru
Joined
Oct 21, 2009
Messages
1,448
Thanks for the reply.
Sorry, yes, I think I was lumpin the builds together...
I've changed from questioning to confused (not very difficult for this pea brained driver) re: your tub's floor pan changes ("frnt & rear").
Sounds like you'll raise the bed and meet that hight in the cab area?
There's 5 inches from my head to the roof, with my eyes already pretty close to the top of the windshield (the latter, 1 reason I wanted to drop the driver's floor).
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Yeah I know. Work and soccer have kept me pretty busy. And I am trying to get "Ol' Red" upgraded as I move along. I hope to have it going the next couple days and post a few pics of the new look.

I am in the process of ordering two roll cages also. One for the streetrod halfcab and one for the '68 halfcab. They will both be the "through the dash" kits, with one 3" lower to fit the chopped Bronco. I will be cruising over to Dubuque Iowa to Extreme Custom Parts and Fabrication to pick these up, as it would be much cheaper than shipping them.

My priority is to get the roll cage in the '68 first, and my son would be driving that every so often. Then I will get back on the chopped project, and will FOR SURE post some new pics.

Well, I better get to soccer practice. If all goes well I will be posting pics of "Ol' Red" tomorrow with the 2.5" lift, rebuilt engine, PS,PB, and new 33" Duratrac tires! Cool! :cool:
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Well I got Ol' Red going again. Got rid of the tired original motor and the old Dana 30 drum brake axle. Added PS while I was at it (along with the new 33's and wheels). Yeah, my son had to pose for us as he has become attached to this project. Of course he won't get too much driving time until I get the roll cage installed. Although I did let him take it around the housing development. :-X

I guess I could have started another thread but oh well. Maybe now I can get some work done on the rod, which is what this thread is all about! ;D
 

Attachments

  • 100_6920.jpg
    100_6920.jpg
    93.5 KB · Views: 115
  • 100_6921.jpg
    100_6921.jpg
    92.6 KB · Views: 121

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
Marty, Behemoth

Just curious did you go with single or double adjustable coil overs?
Front?Rear?
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
for the front I have qa1's they are I guess dual adjustable, with the nuts and the other with the knob on the bottom.

Still running the bags in the rear suspension and adjusting to them.
 

Attachments

  • DSC00002 (Medium).JPG
    DSC00002 (Medium).JPG
    59.1 KB · Views: 76
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
I have the same MS1375 (Jegs 3375) QA1 shocks as behemoth. The rear shocks I went with are Aldan Model 654 13.4".
 
Last edited:

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
Thanks guys for the info.
Since I doubt that I will be at the drag strip much (at least at this point) I think I will stick with single adjustables coilovers brand will be "Strange". The icing on the cake is there is even a local place here that sells what I am after for 298.00 a pair.
S5204 /with recommended 10" springs(springs not included in price)

I was going to pick the rear coilovers up today but... I heard back on an offer I made on a engine and transmission, the fellow may accept and I will need all of my cash to purchase it.

4.6 cobra engine and 5 speed transmission. Also will get the ECU and harness, which leads me to another question. I seen Behemoths posting, on the harness did you ever decide on what you are doing Marty? Will you be converting to the earlier Mustang items? I was wondering about other items such as ignition, pedals etc?

I tossed out a question to "modman"
 
Last edited:
Top