• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Msd box

dgbronc

Jr. Member
Joined
Jan 1, 2010
Messages
59
Loc.
Bainbridge, GA
Anyone running one of these boxes. Have a ford racing 302 boss crate motor with sniper Efi and having trouble with it loading up on low rpm acceleration. My understanding is with the extra spark this should help burn fuel at heavy acceleration at low rpm. Getting ready to wire up and give a try. If you are using just wondering why or what your symptoms where before adding.
Thanks
 

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890
Love my 6A. Symptoms? Too many Duraspark ignition box failures. I've also got a HEI module bolted to the fender skirt as my backup ignition for when the MSD fails.
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
First, you have a tune issue more than likely, not an ignition issue.

What do your plugs look like? Wrong plug heat range could do what you say.


Set the plug gap for the ignition system you are using, an MSD will be wider out to 60 or so.

Check easy cheap stuff first.
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
Love my 6A. Symptoms? Too many Duraspark ignition box failures. I've also got a HEI module bolted to the fender skirt as my backup ignition for when the MSD fails.

Funny, my backup is second flamethrower coil and another msd 6a box. Plug and play
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
I've used them for 30 years they are really solid. Unless you are running a lot of cylinder pressure (high compression) or a cam with a bunch of overlap a stock Ford ignition with good quality parts should be more than fine. What is your idle vacuum? That is a good indicator of what your tuning challenges are.

With EFI you can usually get the AFR and spark timing perfect to get a smooth idle and clean performance. But the Ford Racing 302 may not have enough low speed torque no matter how you tune it.

Tuning from my laptop a gazillion miles away I would recommend more ignition advance down low and then cut it back as RPM and load rises. When you are at your cruise RPM with low throttle angle and high vacuum you can keep bringing in more advance to clean up the off idle response. You can get 30-40 degrees. But you need to manage your curve so that at higher loads (like when you floor it) the timing drops down to a much lower number like 24-26. You usually have two curves - WOT and cruise. Then the EFI extrapolates between to points. I would start by having someone else drive and you start by adding a little bit of timing at those data points.
 
OP
OP
D

dgbronc

Jr. Member
Joined
Jan 1, 2010
Messages
59
Loc.
Bainbridge, GA
Crate 302 boss 345hp
9.0.1 compression
B3030 hydraulic roller camshaft
3.00 stroke forged neutral balance crank
4.000 lightweight forged pistons
Forged 5.090 I-beam connecting rods
X306 gt 40 heads
Cam has a .284/.284 duration and a .480/.480 lift
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
Ford does not share dyno data which is interesting. Looking at the specs and the engine size my guess would be it is not going to be a real killer at very low rpm (under 2000). But it should run clean and pull clean from low rpm.

What is your cruise rpm? If you do not have enough gear that could be causing all your problems.
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
350 gears with nv3550 I purchased truck At end of build would rather have had 411 or 456

Agreed.

I have yet to hear anybody regret going to a lower ring and pinion gear. But often some of us wish we had gone lower.

351W (kind of built)
C4
4.11
35's

Wish I would have gone 4.56's and I have plenty of power but gearing typically makes a difference that horse power can't.

All for not though because I want to go to a 4R70W so it looks like 4.88's are in my future, lol.
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
You can get a real life simulation of lower gears by dropping your trans down a gear. Hypothetically your cruise rpm is 2000 rpm at 50 mph. If you put the trans down a gear and get to 2000 rpm. It will be a lower speed. Now the engine will be more responsive because of the lower gear and see how it feels. Depends a lot of the trans ratios for how close this will work.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
B cams are not known for good idle and more tuning is likely needed. Highly doubtful its ignition related even then a msd box is not needed. I personally dont care much for them seen to many fail yes stock systems fail but Ive seen way more msd's fail for the numbers that are out there stock is more relieable.
As was mentioned gearing and tire size may also factor in. What sounds like a good engine is not always well suited for a particular vehicle. camshafts are a big key to overall performance and the B cam may be more than your bronco needs remember the B cam is more of a topend cam for lite wieght vehicles than it is for a 4wd. Not saying it cant be run but it may require more tuning and changes to gearing to get it good,.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
I've run a couple different multi spark CD boxes (never the MSD brand). I find they tend to clean up idle a bit, I can usually drop idle speed about 100 RPM with one. The latest one I got is the Summit house brand (made by Intellitronix here in the USA) so I could take advantage of the electronic timing curve. But my engine is completely different than yours. Low compression, iron head, mild cam that can't rev past 4500.
 
Top