• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

New Rear Drum Problem

BoureeOne

Bronco Guru
Joined
Mar 28, 2011
Messages
3,068
Loc.
Madisonville, La
Tell me what is wrong here. This is the WH rear drum brake kit. The shoes are part # 3118. I have a 1966 wagon, small baring, 10" drums. The shoes are 2 1/2 " wide. The pin to put the retainer springs on the shoes are 2" long. Either these are the wrong shoes, or the wrong pins got put in the kit. I don't have enough room the connect the bottom cup of the spring, let alone go all the way through the spring and top retainer. Any help would be appreciated.

Scott
 

Attachments

  • IMG_3924.jpg
    IMG_3924.jpg
    88.2 KB · Views: 96
  • IMG_3925.jpg
    IMG_3925.jpg
    79.6 KB · Views: 88

Major Tom

Contributor
Sr. Member
Joined
Feb 15, 2012
Messages
597
brakes

I just did a brake job on my 1966 u13 .I ordered the brakes through Rock Auto along with all new hardware. I had the same problem with the spring retainer pin being too short I ended up cleaning the old pins up and used the new springs. You are correct on the size 10x 2.5 on the rear and 11x2 on the front
 
OP
OP
BoureeOne

BoureeOne

Bronco Guru
Joined
Mar 28, 2011
Messages
3,068
Loc.
Madisonville, La
Here is the how short the pin is. When I call O'Reilly's, they tell me their pads are 1 7/8" inches wide. So trying to confirm, is the pin too short, or pads too wide.
 

Attachments

  • IMG_3926.jpg
    IMG_3926.jpg
    87.4 KB · Views: 101

Hozr

Bronco Guru
Joined
Oct 15, 2011
Messages
1,439
Loc.
Rogue Valley, OR
I had all sorts of incorrect parts in my drum rebuild kits. I had to reuse the old pins and one of the adjusters due to mis packaging....multiple times.
 
OP
OP
BoureeOne

BoureeOne

Bronco Guru
Joined
Mar 28, 2011
Messages
3,068
Loc.
Madisonville, La
Well you guys were right, it was the pins. Here is the difference between the original pin and the pin in the kit. I had to go to O'Reilly's and they just let me go through spring kits on the shelf until I found a kit with pins long enough. Brakes are now together. Hope I did them right.
 

Attachments

  • IMG_3927.jpg
    IMG_3927.jpg
    55.5 KB · Views: 102
  • IMG_3923.jpg
    IMG_3923.jpg
    90.1 KB · Views: 121
  • IMG_3930.jpg
    IMG_3930.jpg
    123.9 KB · Views: 137
  • IMG_3931.jpg
    IMG_3931.jpg
    107.8 KB · Views: 137
  • IMG_3932.jpg
    IMG_3932.jpg
    115.7 KB · Views: 133
  • IMG_3933.jpg
    IMG_3933.jpg
    121.5 KB · Views: 122
Last edited:

redwards69

Sr. Member
Joined
Dec 8, 2014
Messages
367
Loc.
Double Oak, TX
Working on my rear drums now. Hope mine look as good as yours when I'm done! btwv what size are the blocks under your jack stand?
 
OP
OP
BoureeOne

BoureeOne

Bronco Guru
Joined
Mar 28, 2011
Messages
3,068
Loc.
Madisonville, La
Working on my rear drums now. Hope mine look as good as yours when I'm done! btwv what size are the blocks under your jack stand?

Those are actually the remnants of garage header boards that I grabbed at a house that was being built in my neighborhood.

This is the first time that I have ever done drum brakes in my life. Attached is the thread where I asked for diagrams. It helped me a lot. Remember, there are several parts that you must retain from when you take your breaks apart.

http://classicbroncos.com/forums/showthread.php?t=250342
 
OP
OP
BoureeOne

BoureeOne

Bronco Guru
Joined
Mar 28, 2011
Messages
3,068
Loc.
Madisonville, La
I noticed in your pics that you have your u-bolt/spring plates upside down. The beveled edge should go against the spring.

I did not know that. Thanks for the heads-up. What is the reason for the beveled edge to go down?

I also had to get U-bolts what were longer to accommodate the 1" blocks. So I have a set of brand new U-bolts if anyone is looking.
 
OP
OP
BoureeOne

BoureeOne

Bronco Guru
Joined
Mar 28, 2011
Messages
3,068
Loc.
Madisonville, La
Keeps from causing a pinch point on the springs under accel decal and when flexing the springs out.

Funny, I was sitting her talking to my wife and showing her the pic and your comment... And I said it makes sense that they should be flipped because of the flexing of the leafs. Thanks again for noticing it.
 

Can71

New Member
Joined
Oct 1, 2014
Messages
17
Loc.
Redwood city
Bought the same kit from wildhorese and had the same problem. I finally determined they had the wrong pins in the kit. Informed them in December of the problem, having the wrong pins in the kits,sounds like they have not checked/fixed their inventory
 
OP
OP
BoureeOne

BoureeOne

Bronco Guru
Joined
Mar 28, 2011
Messages
3,068
Loc.
Madisonville, La
OP
OP
BoureeOne

BoureeOne

Bronco Guru
Joined
Mar 28, 2011
Messages
3,068
Loc.
Madisonville, La
Bought the same kit from wildhorese and had the same problem. I finally determined they had the wrong pins in the kit. Informed them in December of the problem, having the wrong pins in the kits,sounds like they have not checked/fixed their inventory

Well they might have. I bought this kit 3yrs ago. Just now getting to the point of putting it in.
 

jcpetrson

Sr. Member
Joined
Aug 26, 2012
Messages
435
Brakes are now together. Hope I did them right.

BoureeOne - Thanks for posting those pictures! My PO must have felt that the self adj parts were too much hassle and just ran the bottom blue spring from one brake to the other. I'm not going anywhere until that's fixed.

I don't know why I didn't check my front brake setup after I bought the truck. I did eyeball and have plenty of thickness to last.
 
Top