• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

New warn hub not fitting

STalon89

Full Member
Joined
Oct 15, 2016
Messages
311
Just curious if anyone has had this issue before doing the front disc kit from TBP. Slamming everything back together and drivers side warn hub isnt seating. Checked the splines on both ends and everything looks to be ok. Its almost like the alignment is off. Anyone deal with something like this before?
 

Slednut10

Contributor
Guru? That's funny!
Joined
Sep 26, 2013
Messages
2,398
You may not be able to get the snap ring on the stub axle if thats what you have run into. Very common on the chevy style disc conversion. I had a similar issue two years ago after installing upgraded axles. Outer axle shaft splines were a hair shorter than the opposite side. Hub would only go flush with the axle stub.
 
OP
OP
STalon89

STalon89

Full Member
Joined
Oct 15, 2016
Messages
311
Yea I am just using the outer ring. Thats not the issue tho, the hub wont seat in.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Check the depth of the actual splines in the hub itself. We had a bad batch a year or two ago where the manufacturer figured we didn't need that last quarter inch of spline depth, and while the stock hubs would fit, the aftermarket ones would not.

We did have some that were not so bad, and the Superwinch and Mile-Marker hubs worked, but the Warns would not. But most of them would not fit any aftermarket hub.

See if this is your issue.
If they look deep enough, maybe there are just one or two small burrs that are holding things out. You'd be shocked at how easily a tiny burr on either the aluminum or the steel will feel like a solid stop when it's reached.

Good luck.

Paul
 

tirewater

Bronco Guru
Joined
Jan 28, 2011
Messages
1,046
Loc.
San Francisco Bay Area
Check the depth of the actual splines in the hub itself. We had a bad batch a year or two ago where the manufacturer figured we didn't need that last quarter inch of spline depth, and while the stock hubs would fit, the aftermarket ones would not.
Paul

Hard to tell if the issue is if the hub doesn't go far enough in versus going in at all.

The rotor/hub combo I bought 1.5 years ago had the issue that Paul mentioned where the Warn locking hub wouldn't go in far enough to get the large snap ring on. It was only off by about 1/16-1/32 of an inch, so I filed the Warn hub to fit.
 

PDQ

Contributor
Full Member
Joined
May 6, 2012
Messages
297
I had the same issue. I/ you may have a slightly bent spindle which was causing the outer and inner splines to bind when trying to slide the hub into the rotor sleeve. To solve it, I threaded a long bolt into the end of the axle and used a small bottle jack to lift the bolt slightly. With pressure on the bolt, it now allowed the hub to line up and go all the way in. Only issue was that the hub was a little sticky when fully assembled and locking and unlocking it, but after fighting the install for so long, I'll chase that issue down later.

Hope it helps.
 

DC_Gearhead

Sr. Member
Joined
Dec 28, 2015
Messages
660
Hard to tell if the issue is if the hub doesn't go far enough in versus going in at all.



The rotor/hub combo I bought 1.5 years ago had the issue that Paul mentioned where the Warn locking hub wouldn't go in far enough to get the large snap ring on. It was only off by about 1/16-1/32 of an inch, so I filed the Warn hub to fit.



I “filed” mine too....with a grinder. Fit perfect now.


Sent from my iPhone using Tapatalk
 
OP
OP
STalon89

STalon89

Full Member
Joined
Oct 15, 2016
Messages
311
Thanks for the replies. Ill be diving back into it one night this week to try some of this
 
Top