• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Project grocery getter

chuck489

Full Member
Joined
Jul 5, 2008
Messages
317
Loc.
Dahlonega, GA
I can't work metal, so I don't know how hard this would be, but what about using vent windows on the top? Passenger side vent window on the driver's side and reversed on the passenger side. I think that would be neat. Just my .02
 

br0nc0xrapt0r

Loves pickles
Joined
Sep 28, 2007
Messages
5,439
I was thinking about that, I like em low. Prob is in the front. I was running
35's with a front 1.25 block and some sort of rear ad a leaf and the tires would scrub leaving my driveway. I'd have to cut so much in the front that I'd loose the bronco character and it would become a buggy.

3 link front and 4 link rear with ballistic adjustable coil buckets on each corner then. ;D
 
OP
OP
P

ponyracer

Sr. Member
Joined
Sep 30, 2009
Messages
706
Loc.
Crestview, Fl, 32539
I can't work metal, so I don't know how hard this would be, but what about using vent windows on the top? Passenger side vent window on the driver's side and reversed on the passenger side. I think that would be neat. Just my .02


I've been thinking about that, I happen to have some spare doors that I could use the frames out of. Just have to rebuild the rubbers and pivots on the glass. I'll look into that today, thx for pushing that idea to the front.
 
OP
OP
P

ponyracer

Sr. Member
Joined
Sep 30, 2009
Messages
706
Loc.
Crestview, Fl, 32539
So what did the wheel base end up at?

Right at 105"

Got ALOT of welding done today, got the sunburn to prove it lol. got the first coat of bondo on the sides also. Finished welding up the bulkhead and got most of it seam sealed.

DSC04912.jpg


DSC04913.jpg


Am I going to go to hell for putting a modern jeep part in a 37 yr old ford?

DSC04911.jpg

DSC04910.jpg
 
OP
OP
P

ponyracer

Sr. Member
Joined
Sep 30, 2009
Messages
706
Loc.
Crestview, Fl, 32539
Still have to make the fuel tank, fab up a hose to go to the box and roll the cover because it's to flat to follow the contours of the bronco. Box is from my 01 xj that I wheeled to death and hauled for scrap last week, RIP my friend.

Before all you run out to your xj with a sawsall, the box fits like crap and I shouldn't have done it. I had to cut the box in 3 pieces and do a BUNCH of tweaking and trimming to get it to follow the body roll. That mod alone took like 3hrs, and it's not done yet, I'm not sure how bad the door is going to be to roll.
 

camomog

Full Member
Joined
Sep 10, 2008
Messages
254
Loc.
Reno, Nv.
I get motivated seeing your progress but I think it hit 33 today and snowed off and on most of yesterday. For the door can you use the sheet metal you cut out of the quarter?
 
OP
OP
P

ponyracer

Sr. Member
Joined
Sep 30, 2009
Messages
706
Loc.
Crestview, Fl, 32539
Ugg, it was 74 degrees here today. I was sweating in my coveralls in NOVEMBER. Thats just not right lol.

Ya I'll check and see if i have a big enough piece left, I may just do that, thanks.
 
OP
OP
P

ponyracer

Sr. Member
Joined
Sep 30, 2009
Messages
706
Loc.
Crestview, Fl, 32539
Well I got a bunch of little stuff done before the rain shut me down. Got the exhaust pretty much done, possibly the best offroad exhaust ever made!! I'll post some pics when it's done.

Got my BC bronco steering shaft installed, very nice, much better than the crap I was using. I also got the dual output saginaw box on it, should be alot nicer to drive.

Also got the front flares mounted, and some bodywork done.

Hopefully tomorrow I can get the top welded up/bondo'd and installed.
 

jperry1290

Sr. Member
Joined
Jul 1, 2010
Messages
920
And I thought that I had a lot of work to do on my rig. The work looks great. How will that bondo hold up off road?
 
Top