• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

pulling left

uncut

Jr. Member
Joined
Jul 12, 2007
Messages
75
an idea of why a 4 wheel disc setup on a 77 with a new 4 wheel disc master cylinder and a new booster is pulling left?

someone said the right caliper needs replaced and i should replace both.

will this 4 wheel disc ever work without hydroboost? i'd hate to replace the whole setup just to find i shoulda gone with the hydroboost because i have the rear discs.

thanks all
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
Sounds like you need to check out your right hand caliper as it may not be sliding on it's mounts or the piston may be stuck. It could also be a bad caliper hose not allowing fluid and pressure to the caliper.

There are plenty of guys running 4-wheel disc without hydroboost and without any issues.
 

Dave

Contributor
Bronco Guru
Joined
Aug 25, 2006
Messages
2,264
I would suspect a calliper problem and stated above. It that isn't it, do you have it plumbed in correctly? H-Block, balance valve, etc... I fixed one that both rears and left front on the rear piston and only the front right on the front piston. Hydroboost does the same thing as the vacuum booster only better. Shouldn't effect anything as long as you use the same master.

Could also be caused by listening to FM radio. Try tuning to AM talk and see if it pulls to the right.;D
 

bigmuddy

Contributor
Bronco Guru
Joined
Dec 28, 2004
Messages
8,071
Loc.
Marthasville Missouri
Might be a long shot but double check the tightness and condition of you wheel bearings. I have a drivers side wheel bearing that continually works loose. I discovered it when I had a hub that had blown and then took out the bearing with metal particles. Anyway, it was pulling hard to one side.

Best of luck,

Ben
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Could also just be dirt and rust buildup on the caliper sliding surfaces. Might want to pull the calipers and clean and lube the sliding surfaces.
 
OP
OP
U

uncut

Jr. Member
Joined
Jul 12, 2007
Messages
75
as a matter of fact, my front drivetrain labors to keep up with my rear, as though I am always driving up hill. doesn't happen when in 2H. So I'll be chasing down all of these suggestions and post results in a day or two.

THANK YOU
 
OP
OP
U

uncut

Jr. Member
Joined
Jul 12, 2007
Messages
75
e brake adjustment???

after bleeding the brakes, i noticed that the rear calipers are loose. there shouldn't be too much play when at rest, should there? shouldn't the pin in the caliper for the ebrake tighten up? mine is about 1/8 inch back from the disc.
is it possible with the new cadillac seville calipers that he ebrake won't tighten properly? do i need to modify the e brake cable? i could put a tube around the front cable to push the plate away from the bolt that holds it by an inch. anybody have any experience with this caliper issue? am i off to think the e brake controls adjustment of the rear caliper?

also, the shoe has broken away from the plate that it is supposed to be attached to. so that can't help. eventually, it'll just snap the rivets and slide out of the caliper, so i guess i should replace that. on the other side, the whole shoe rattles-i don't know whether it is designed that way, but i'm guessing not.

thanks for help!
 
Top