• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Rear Quarter Pannel

bronco_boy_66

Jr. Member
Joined
Sep 17, 2002
Messages
145
Loc.
Indiana
I have worked my way to the passenger's side quarter pannel. It was pretty rough, so I torched it out. With most of it out of the way I began drilling spot welds. When I got to the back, the lip of the quarter pannel is behind another piece, but it is welded in. How do I get the rest of it out of there?
 

DJM75

Sr. Member
Joined
May 26, 2001
Messages
747
Loc.
Washougal
I too would like to know. As I have to change out both of my quarter panels this summer.
Don
 

canadabronco

Full Member
Joined
Jul 1, 2001
Messages
315
Loc.
Whistler, British Columbia, Canada
It seems to me like we are stumped. I know exactly what you are talking about. I didn't have a problem because I replaced the corners first. You obviouly need to drill out the welds but there are some tight spots in that area. Good luck.
 
OP
OP
B

bronco_boy_66

Jr. Member
Joined
Sep 17, 2002
Messages
145
Loc.
Indiana
Do you think it would be worth it to replace the corners? They aren't to bad, but sense it makes it easier...
 

canadabronco

Full Member
Joined
Jul 1, 2001
Messages
315
Loc.
Whistler, British Columbia, Canada
If your corners are fine then keep them. I had a real hard time getting mine lined up. They are welded in now but they are not perfect. They don't come with anything to screw the taillight into either. I stll haven't figured that one out yet.
 

El Jefe

Bronco Guru
Joined
Oct 20, 2002
Messages
1,166
[quote author=canadabronco link=board=5;threadid=19682;start=0#msg151157 date=1057597893]
If your corners are fine then keep them. I had a real hard time getting mine lined up. They are welded in now but they are not perfect. They don't come with anything to screw the taillight into either. I stll haven't figured that one out yet.
[/quote]

replace the stock taillight with LED tails...
 

canadabronco

Full Member
Joined
Jul 1, 2001
Messages
315
Loc.
Whistler, British Columbia, Canada
[quote author=Sr.Bronco link=board=5;threadid=19682;start=0#msg151171 date=1057600823]
[quote author=canadabronco link=board=5;threadid=19682;start=0#msg151157 date=1057597893]
If your corners are fine then keep them. I had a real hard time getting mine lined up. They are welded in now but they are not perfect. They don't come with anything to screw the taillight into either. I stll haven't figured that one out yet.
[/quote]

replace the stock taillight with LED tails...
[/quote]
I don't mean to steal the thread but what will the LED's do for mounting?
 

67ster

Bronco Guru
Joined
Feb 18, 2002
Messages
1,572
You mean the mounting tabs are missing from the replacement panel? That sucks !! My solution would be to snip some out of sheetmetal and weld them in .
 
OP
OP
B

bronco_boy_66

Jr. Member
Joined
Sep 17, 2002
Messages
145
Loc.
Indiana
Thanks for the info. I cant believe they didnt put anything to mount the tail lights thought. Its not like they are optional or something. ::)
 

CT.boy

Jr. Member
Joined
Feb 4, 2002
Messages
112
Loc.
Southern Connecticut
[quote author=bronco_boy_66 link=board=5;threadid=19682;start=0#msg150944 date=1057528231]
I have worked my way to the passenger's side quarter pannel. It was pretty rough, so I torched it out. With most of it out of the way I began drilling spot welds. When I got to the back, the lip of the quarter pannel is behind another piece, but it is welded in. How do I get the rest of it out of there?
[/quote]

I did this a while back and was stumped at first. I trimmed as much of the quarter as I could along the back , just about down to flush. Then I worked my way up from the bottom drilling spot welds as I went.
When I came to where the quarterpanel was sandwiched between the other panels I spread them apart just enough with a screwdriver to see where the next spotweld was. I did this carefully so I didn't stretch or distort anything.
Once I drilled out that spot weld I again worked my way up carefully prying the panels slightly to reveal the next spotweld and drilled that out.
Once I worked my way to the top the quarter was out without any damage to the other panels.
I hope this makes sense. ???

Dave
 
OP
OP
B

bronco_boy_66

Jr. Member
Joined
Sep 17, 2002
Messages
145
Loc.
Indiana
So you just bent the other pannels out a little bit to get the rest of the quarter out, and then bent it back when you replaced the quarter?

Also, how did you put those welds back in? Ther is no way you could get to those with the quarter in place.
 

CT.boy

Jr. Member
Joined
Feb 4, 2002
Messages
112
Loc.
Southern Connecticut
Actually it is more of prying them apart just enough to see the spotweld between them and then drilling it out from the front. By starting at the bottom and working up you are not really stretching any metal to look between tthe panels. Sorry my explanation is so terrible.

Once all the spotwelds were drilled, the piece of the sandwiched quarter panel came right out.

As far as welding in the replacements, I will probably be asking you how to do it as it will be a while before I get back to that part of the project.

I hope someone comes along who can explain this better. ::)

Dave
 

2badrotties

Just a Bronco guy !
Joined
Sep 10, 2002
Messages
6,854
Loc.
Niskayuna N.Y.
It is hard to explain. You will need to have the tire off first of all. You must reach up into your new quarter panel ( the rear of it ) from under your wheel well. You have to drill your holes so that you are welding all three of those pieces together again. You drill the new quarterpanel and weld IT and the other piece to the tail light panel. Don't drill holes through the tail light panel and if you do , you might be able to weld them through the tail light opening but you won't get to all of the holes through there. Can you understand what I'm saying ?
 
OP
OP
B

bronco_boy_66

Jr. Member
Joined
Sep 17, 2002
Messages
145
Loc.
Indiana
Taking the wheel of will help, and I will be able to get to some of the holes to weld. There is still a section of the quarter that is between another piece (toward the front of the truck) and the tail light section that blocks me from getting to the lip of the quarter.
 

Gummi Bear

Bronco Guru
Joined
Jul 8, 2003
Messages
3,647

replace the stock taillight with LED tails...

Where can I find some LED tail lights? I want to replace everything with LED when I can, (markers, running, tails)but where can I begin looking for them? I was considering the LED lamps fom the local parts store, but wondered if there is a better alternative. Please advise.
 

El Jefe

Bronco Guru
Joined
Oct 20, 2002
Messages
1,166
I've found then the cheapest at TSC (Tractor Supply Company) I'm SURE there's one in Texas ;D

You will have to take them apart and fit them to you r application. Let me know how it goes as i plan on doing the same but aren't anywhere near that step in my re-build...
 
Top