• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Rear shackle help

Jonathan_Cole

Full Member
Joined
May 11, 2020
Messages
154
I'm in the process of fighting with a Toms 2.5 lift. I can't get the shackle to line up to put the bolt in. The only way I've got the bolt to go in is remove the leaf spring and orient the shackle straight up. Of course, once I do this I can't get the leaf spring bolt in. Also, the instructions state that the closed side of the shackle goes forward but, it appears to fit better and rotate better if it's facing the rear. Any assistance would be appreciated.

Sent from my Pixel 3 XL using Tapatalk
 

billh1289

Contributor
Sr. Member
Joined
Jul 2, 2006
Messages
496
Loc.
Jackson, NJ
I'm in the process of fighting with a Toms 2.5 lift. I can't get the shackle to line up to put the bolt in. The only way I've got the bolt to go in is remove the leaf spring and orient the shackle straight up. Of course, once I do this I can't get the leaf spring bolt in. Also, the instructions state that the closed side of the shackle goes forward but, it appears to fit better and rotate better if it's facing the rear. Any assistance would be appreciated.

Sent from my Pixel 3 XL using Tapatalk
Are you installing the shackle end first?
 

EPB72

Contributor
Bronco Guru
Joined
Jul 13, 2019
Messages
1,216
Loc.
Pleasant Hill, CA
This is the way I do it many many times without issue,, assuming you have a the leaf pack with the double wrap on one end .. the double wrap end goes to the front ,, install that end first,,,install the shackle on the other end .then either lift into position to install shakle end into frame bracket ,,or use your jack to lift spring into postion to install shackle into frame hanger this way your not fighting the weight of the spring,, repeat other side then work on attatching rear housing to springs......

final torque of shackle and spring eye bolts with full vehicle on suspension....And Yes closed end forward on shackles...
 
OP
OP
J

Jonathan_Cole

Full Member
Joined
May 11, 2020
Messages
154
I've tried that. It's still not working. It's almost like the bushing is too thick.


Edit, to be clear, this end faces the rear?

Sent from my Pixel 3 XL using Tapatalk
0bb77a664296efad19ec8c0685ee5f7d.jpg
 
Last edited:

EPB72

Contributor
Bronco Guru
Joined
Jul 13, 2019
Messages
1,216
Loc.
Pleasant Hill, CA
I've tried that. It's still not working. It's almost like the bushing is too thick.


Sent from my Pixel 3 XL using Tapatalk
Like too wide for the ears of the hanger?? if so you can spread them out a bit so the shackle slides in , lots of times there sqished a little,, or a little indent/ wear from the original bushing sleeve..
 
OP
OP
J

Jonathan_Cole

Full Member
Joined
May 11, 2020
Messages
154
Like too wide for the ears of the hanger?? if so you can spread them out a bit so the shackle slides in , lots of times there sqished a little,, or a little indent/ wear from the original bushing sleeve..
Yes, I've tried to open them up. They're not budging.


Edit, I got them opened up a little. It goes in easier but with the spring on it I'm still half the bolt hole from lining up.


Sent from my Pixel 3 XL using Tapatalk
 
Last edited:
OP
OP
J

Jonathan_Cole

Full Member
Joined
May 11, 2020
Messages
154
I got the outside hole lined up enough to get the bolt to thread in, now the inside won't line up.

Sent from my Pixel 3 XL using Tapatalk
 

Oldtimer

Contributor
Jr. Member with Sr. moments
Joined
Feb 4, 2005
Messages
1,801
Loc.
Sunnyvale, CA
I struggled with WH 2.5 lift install.
I had to open the shackle a little to get bushings to install.
I took an old spring shackle bolt, ground a taper on it, and used it and a Big Ford Hammer to get the holes in line, then drove taperd pin out with new bolt.

2023-02-25_105913.jpg
 
OP
OP
J

Jonathan_Cole

Full Member
Joined
May 11, 2020
Messages
154
I'm at the point that I wish I'd have left this thing alone, or paid someone else to do it. I believe the flange on the bushing is just too big. I removed the spring from the shackle just to see if I could get the shackle to drop in. It won't. It seems like the bushing on the inside won't allow it to drop in as it should.

Sent from my Pixel 3 XL using Tapatalk
 

billh1289

Contributor
Sr. Member
Joined
Jul 2, 2006
Messages
496
Loc.
Jackson, NJ
I'm at the point that I wish I'd have left this thing alone, or paid someone else to do it. I believe the flange on the bushing is just too big. I removed the spring from the shackle just to see if I could get the shackle to drop in. It won't. It seems like the bushing on the inside won't allow it to drop in as it should.

Sent from my Pixel 3 XL using Tapatalk
Hard to say without seeing it but you might just need to spread the ears more. I use a long bolt as a spreader…(not my pic but a good example)
1677356143631.jpeg
 
OP
OP
J

Jonathan_Cole

Full Member
Joined
May 11, 2020
Messages
154
Just for future reference for anyone else. I used previously posted advice and ground a point on one of the old bolts. Unfortunately with Jack pressure to put the shackle where it needs to be, the shackle popped out as soon as I removed the bolt. I cut the head off and drove it through with the new bolt. Thanks for the help.

Sent from my Pixel 3 XL using Tapatalk
 
Last edited:

Oldtimer

Contributor
Jr. Member with Sr. moments
Joined
Feb 4, 2005
Messages
1,801
Loc.
Sunnyvale, CA
The only way I've got the bolt to go in is remove the leaf spring and orient the shackle straight up.
So the shackle will fit.

Install shackle on spring. Nut loose so shackle can pivot.
Do not attach spring to front hanger.
Orient shackle so that it it straight down when installing spring.
2023-02-25_135720.jpg

Install shackle and bolt in rear hanger.
Use ratchet strap to pull spring forward as you raise it with floor jack.
When close, use tapered pin/bolt to get holes lined up.
2023-02-25_105913.jpg

Take a nap.
Do other side.

Edit: I type slow. I see you got it done.
 
OP
OP
J

Jonathan_Cole

Full Member
Joined
May 11, 2020
Messages
154
So the shackle will fit.

Install shackle on spring. Nut loose so shackle can pivot.
Do not attach spring to front hanger.
Orient shackle so that it it straight down when installing spring.
View attachment 897520
Install shackle and bolt in rear hanger.
Use ratchet strap to pull spring forward as you raise it with floor jack.
When close, use tapered pin/bolt to get holes lined up.
View attachment 897521
Take a nap.
Do other side.

Edit: I type slow. I see you got it done.
I have one side done. Currently fighting with the passenger side.

Sent from my Pixel 3 XL using Tapatalk
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Glad you got it done, but sorry to hear it was such a bear.
For future reference as well though, the orientation of the shackle depends on what type of shackle it is.
The original factory shackles do orient with the open end facing the rear, and the closed end facing the spring. That is the proper way for a factory shackle.
However, probably every aftermarket shackle reverses that and has it open and facing the spring.
So are you using stock, original shackles, or aftermarket like in your picture?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
And are the springs still loose while you are doing this, or do you have them attached to the axle by any chance?
 
OP
OP
J

Jonathan_Cole

Full Member
Joined
May 11, 2020
Messages
154
And are the springs still loose while you are doing this, or do you have them attached to the axle by any chance?
I have the shackle pictured from Tom's. And, the springs are loose. The axle is actually sitting on blocks on the shop floor. I removed it completely.

Sent from my Pixel 3 XL using Tapatalk
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Maybe the person at Tom’s thought you were using stock shackles. Or, perhaps, if you told him that you had their shackles, they still just got it backwards.
Either that, or there’s in particular mount the same way as stock!
I guess you could get clarification on it from them, but in lieu of that additional information I would generally run it in whichever direction seems to work best.
As it sounds like you were doing.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Regarding the bushings being too wide and causing a tight fit in any of the components, do you have a picture of the bushings installed?
Is there a gap between the bushing and the spring eye itself? Or is the only bushing giving you trouble the one for the shackle?
 
OP
OP
J

Jonathan_Cole

Full Member
Joined
May 11, 2020
Messages
154
It's the shackle bushing. There is really no gap. One wouldn't compress all of the way when I installed it so I put it in the press.


Now that I think about it, the included instructions do not specify stock or Tom's parts for the direction of the shackle.

Maybe I'm doing it wrong.


Sent from my Pixel 3 XL using Tapatalk
 
Last edited:
Top