• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Restoration or modification ?

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
There are many on this forum who can't transform their Bronco enough, even in cases where the original-stock parts are as good or better than the after market offering. On the other extreme are meticulous restorers who will only use NOS parts and do all the inspectors marks.
I bought two of my Broncos new and loved them as built by Ford. The first was a '73 and being new to all this I believed magazine articles and soon dived in with a lift kit from Ruff Country or Rancho. The kits were junk then and I soon regretted making my truck a nightmare to drive and put it back to original configuration. A t-bone accident lost that truck.
The next new Bronco was a '77. Still have it and am ready to do a frame off. The question is how far go in either a strict restoration or a resto-mod with fixes that address only the short comings I've learned about over the years?
The same question came up with a '70 428 Cobra Jet Cougar Eliminator I owned. Fortunately someone offered too much $ to refuse. The classic muscle car crowd has more incentive to restore.
Broncos are different but still of historic value.
 

redtail

Sr. Member
Joined
Jul 14, 2010
Messages
621
I feel you there (on the aftermarket parts) Ford did a really good job on the bronco and some of the aftermarket stuff I have seen is pretty wimpy. For most folks, the stock parts are really a good value. (not all, as lift kits have come a LONG way, and really do improve the ability of the rigs for having fun offroad with bigger tires and so forth. But really, you have to buy some GOOD aftermarket parts to match the quality of stock parts.
I see this same thing in engine building all the time, really you don't need h beam rods and a billet crankshaft to make a screamin street machine engine.
A lot of times just a few carefully selected parts to make up for a few shortcomings in the factory design. For me it has been a locking rear diff, and a floor shifter. There will be other mods, but most will involve the use of OEM parts from other cars/trucks.
The thing we oft forget is some REALLY smart people spent a LOT of time designing OEM products, and for us to go in and just slap in some poorly made product with little thought to how it will effect the rest of the truck is, in my opinion a very bad decision
 

patterdale

Bronco Guru
Joined
May 24, 2010
Messages
1,252
You will probably do a little of both. A cage and shoulder belts would be first on my list and others would do a front disc conversion. A 2" lift would also be on my list to get a little better tire on it. I'd probably go the way you mentioned and fix the "shortcomings".
 
OP
OP
J

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
On the subject of lift kits, the front end needs about 2" just to almost level the stance. The other issue was bottoming on any decent size bump. The factory coils were utterly inadequate. The rear springs were too stiff. I think Ford simply transplanted them from the '66 F100 and they were made for hauling a load, not for people to sit on.
I've found that 31" tires do everything needed off road. That's nearly identical to the 9.15 x 15" tires mounted on the Stroppe Baja Bronco and a couple sizes larger than the biggest tires Ford offered. And like the Baja and most Broncos at that time I prefer wheel well cut outs.
Until '76 the brakes were not good. The '77 has power disc breaks and they work fine with reasonable tires, so does the factory Saginaw quick ratio power steering box.
The 302 has plenty of HP but lacks low RPM torque, so a 351 transplant, that was common after Ford introduced this great engine in '69 Mustangs, is appropriate if done as the factory would have done it.
A role bar with shoulder strap-seat belts like newer CJ 5-6s is common sense.
 

redtail

Sr. Member
Joined
Jul 14, 2010
Messages
621
You might try a set of progressive coil springs (I used stock height autozone springs and they work great). you could get a good set of lift coils as well. they also make softer multi pack rear leaf springs now.
Don't forget to keep in mind you need a lift 'kit' not just sprongs (drop pitman arm, tracking bar drop, new degree'd c bushings and the like.
So far in my driving I have found the drums to be surprisingly good at stopping my rig, even with heavy 35 inch tires. But each truck has it's own needs.
I found 31's work well offroad for a hunting rig and or an a-b type driving , but they don't allow you to 'play' in the mud that well. they get you through, but it isn't as fun :p
Eventually I will get a cage and some 5 point belts, as I feel the three point harness is not sufficient in a caged bronco (too much flopping around)
 

mwebb

New Member
Joined
Jan 16, 2011
Messages
5
I used the Wild Horses front springs with + 2" of lift along with the 11 pack rear leaf springs on my 77. What a difference in all the areas you mentioned. Also used the BFG All Terrain 31X 10.5 tires. Truck is in stock form and uncut but looks and is a bit tougher.
 
OP
OP
J

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
Progressive rate springs are surely going in. It would be helpful if venders supplied the specs. on their springs. Moog and TRW replacement progressive springs have the rating in lbs./in., unloaded length, and wire diameter published to help selection.
The 10-11 leaf rears seem to be the answer for the hard ride.
The larger tires may be great in mud. The problem is finding mud in the dessert.
The lift kit I found in '73 was not anything like what they are now, but my experience left a bad taste in my mouth and I have since seen little reason for one, except for huge tires to drive in the non existent mud.
Funny after all this time the Baja is still a great compromise and it is certainly period correct. The front springs were replaced, so were the shocks. The 31" tires look good and work well on and off road without over stressing the brakes, steering, or drivetrain.
 

redtail

Sr. Member
Joined
Jul 14, 2010
Messages
621
I was in the same mindset as you on the 31 inch tires, then I took a ride in a bronco with 35's and it would go more places with open diffs front and rear than mine would go with 31's and posi front and rear! and that was with stock gearing in both rigs (both of our rigs have 3.50 gears, his was 35's and mine was 31's).
 
OP
OP
J

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
A friend at work bought a '69, put a 5.0 HO EFI in and bragged about his great fuel economy. Then he got 36" tires and found his MPGs were worse than the carbureted engine he started with. I haven't seen him in about 10 yrs. but I'd like to know how many parts he's broken. Anyway I think I'll stick with my 31"s.
 

redtail

Sr. Member
Joined
Jul 14, 2010
Messages
621
Yes, that is true. But there are a lot of variables to consider when the big tires go on, the most important of which is the gear ratios and axle strength. If you are not in to hard core 'wheeling' 31's are a great all around tire for the street and offroad. Big tires, lifts and other parts that go with are not for everyone. :)
 
Top