• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Roll pin on distributor

Firemanjay

New Member
Joined
Feb 17, 2014
Messages
29
Loc.
Bakersfield
I need some help. My roll pin on my distributor has sheared off for the second time in 2 years. I have a 351W pretty stock with a duraspark distributor. While driving down the road at 70 mph my engine died after tear down I was able to determine the pin had sheared again. The last time this happened the same way I changed distributors, oil pump, pick up tube and reassembled the motor and ran great. This is a daily driver I drive approximately 10,000 miles a year. I would really appreciate any help thanks.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Several things can cause this. That is actually a shear pin, designed to break before more expensive parts are involved. Anything creating more load on the oil pump/distributor can be the cause.
Is yours a high flow/pressure oil pump?
Sometimes the factory plastic coated timing gear gets shredded and binds up the pump.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Drain the oil and run it through a coffee filter and see if you have allot of trash in it. You gotta drain the oil anyway to remove the oil pump. You want to check the pump drive shaft anyway.
 
OP
OP
F

Firemanjay

New Member
Joined
Feb 17, 2014
Messages
29
Loc.
Bakersfield
I drain the oil everything looked good and everything was good and clean in the filter. I ran the oil pump in a bucket and it works like it should. I also opened the pump up and everything looks good. I will reassemble the motor next week and check clearances on the distributor and cam shaft. Thanks for all the help.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Maybe just a piece of crap roll pin or in an oversized roll pin hole. You can get high grade roll pins from Mc Master Carr.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
The original roll pins were not a single almost 360° roll, they were a spiral of several layers. If the dist's you're getting have the almost 360° type roll pin then I'll suggest finding another such roll pin that will fit inside of the first one. Drive it in with the seam placed opposite of the first one.
 

69_Sport

Full Member
Joined
Nov 5, 2014
Messages
286
If you have an oil pressure gauge, what was your oil pressure before the pin sheared?
What weight oil do you use?
I've only had experience with the pin shearing twice. Both times either a higher volume or a higher pressure pump was being used.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
You really don't want to increase the strength of the pin for more than it was designed for. You want it to shear before the oil pump's extension shaft twists off. If the oil pump extension fails first, your distributor will keep working, and the bearings won't be getting any oil.
If the holes are sloppy, there's nothing wrong with drilling a new hole through the gear and shaft. Just make sure you don't drill in the same plan as the original hole.
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
Maybe just a piece of crap roll pin or in an oversized roll pin hole. You can get high grade roll pins from Mc Master Carr.

THIS.

The quality and type really matter. I worked at a company that sold roll pins and we had a pile of claims when they starting shearing. Chinese vendor over heat treated them and they would snap. Using a solid pin is not the way to go - the roll pin is springy and can take the repeated shock of load / unload driving the oil pump and spring back.
 

74bob

Full Member
Joined
Jun 1, 2003
Messages
229
Loc.
Broomfield,CO
Had that happen to my BIL's Bronco many years ago coming up to Eisenhower tunnel on I70 he stomped the pedal to the floor and when it downshifted it promptly quit. I had to turn around and retrieve him and tow his Bronco to the top. Pulled cap and found no rotor movement. Pulled distributor to find the pin had sheared so we pulled the pan and oil pump and found something like a piece of carbon wedged in the oil pump gears. Cleaned everything out and put it back together and it ran fine until we built a new engine for it.
 

56f100bbw

Contributor
Bronco Guru
Joined
Feb 3, 2008
Messages
2,406
Loc.
Tucson / lakeside AZ
I had a tioga Rv 460 engine that did that on a trip to San Diego what a pain on the side of the hwy 8 hours 27000 miles on the engine never did it again
 

5001craig

Contributor
Bronco Guru
Joined
Nov 3, 2013
Messages
1,180
I have a friend that has gone through distributor pins in his stout 351W. I was researching this sometime back and found distributor clearance is a common cause of this. The article was in performanceboats.com but I've been looking for the exact article for a day now off and on and can't find it.

Lots on the web about high volume oil pumps, oil viscosity, etc. This article really seemed interesting regarding this topic but I can't seem to find it now. I'm not a quitter...
 
OP
OP
F

Firemanjay

New Member
Joined
Feb 17, 2014
Messages
29
Loc.
Bakersfield
Thanks for all the responses. I’m running a normal oil pump not a high volume. I’m running valvoline 20/50 oil. When the motor died just cruising at 70 mph down the road I had 40 to 45 psi oil pressure. I am currently looking into the clearance on the distributor and camshaft. The article a gentleman posted on the first page talked about pulling down on the distributor during a load. Hopefully I will do some mock up work this week. Thanks again for all the information always trying to learn.
 
Top