• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Seat relocation bracket - gauging interest

bigjhoov

nobody
Joined
Apr 10, 2005
Messages
3,583
Do you need more leg room?

I've developed a bracket that allows you to relocate your seat 2 or 4 inches rearward for addition leg room utilizing the factory mounts and sliders, without drilling any additional holes in your tub. And, it only raises the seat 3/16 of an inch. It will also allow you to place the seat 2 or 4 inches forward of the factory location if necessary. The pictures show a seat that's been moved back 2".

Haven't nailed down pricing yet. As always, better pricing comes with quantity, That's why I'm just gauging interest at this point.

1.jpg


4.jpg
 
Last edited:

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Nice piece Big J. A different angle on things, but I bet you get some takers.
It always depends on the price (almost) but looks like you've got yourself a good idear.

If you don't have to drill for the new locations, then your bolts are just 3/16" (or thereabouts) long? Just enough to go through the plate, but not enough to stick past it?
Seems like you'd want more engagement than that to me. At least for the rear two bolts that take all the heat when in a "rapid deceleration" maneuver.

Good luck.

Paul
 
OP
OP
bigjhoov

bigjhoov

nobody
Joined
Apr 10, 2005
Messages
3,583
Nice piece Big J. A different angle on things, but I bet you get some takers.
It always depends on the price (almost) but looks like you've got yourself a good idear.

If you don't have to drill for the new locations, then your bolts are just 3/16" (or thereabouts) long? Just enough to go through the plate, but not enough to stick past it?
Seems like you'd want more engagement than that to me. At least for the rear two bolts that take all the heat when in a "rapid deceleration" maneuver.

Good luck.

Paul

The bolts that affix the bracket to the seat are 3/8" x 1" long, and are secured with a locking nut. The factory bolts that affix everything to the tub are 5/16".
 
Last edited:

BigBlueBronco71

Full Member
Joined
Jul 14, 2013
Messages
310
Loc.
Santa Maria, CA
Impressive, very cool design, and it reinforces the floor at the area as well, I would be interested if I were not considering floor tubes at the moment, I'm sure you'll have interest
 

papy

Contributor
Sr. Member
Joined
Jun 13, 2012
Messages
905
oddly enough i was just thinking about moving the seat back on my 66. Hard to change gears on a 3speed with a floor shifter when your right knee is resting on the passengers seat...

nice work
 

englewoodcowboy

Lick Creek Restorations
Joined
Jul 25, 2010
Messages
4,201
Great idea. I like the fact it can be installed in a few minutes and reversed if need be. Kudos!
 

66horse

Bronco Guru
Joined
Jan 7, 2002
Messages
3,394
Cool product. Nice design.

I love seeing new stuff for our rigs.
 
OP
OP
bigjhoov

bigjhoov

nobody
Joined
Apr 10, 2005
Messages
3,583
Thanks for all the input guys, I'm working on getting some pricing on runs of 10-20 at a time. I anticipate pricing to be well under $100.
 
Top