• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Seriously, can a D20 not leak?

KS.76Sport

Sr. Member
Joined
Mar 20, 2008
Messages
354
Loc.
Wichita, KS.
Okay, I know that a concenses (from what I have read on here) is "If your D20 aint leaking, somethings wrong". I refuse to believe that a leak has to be something that is just accepted. Is there anyone out there that has had success in sealing up their D20? If so, how did you do it? And what materials, prep, application etc did you use to do it?
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Yes. Teflon thread sealant on all the bolts and plugs. Well, there's only 8 that are blind. Other than that good gaskets and seals.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
took a mix of 4 different chemicals to seal mine nicely. Teflon paste on the pipe plugs. Anarobic in some places, Hylamar in others (forgot which went where), and a touch of RTV to seal the splines to the yoke. Each had it's reason for being used instead of another.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
I also used a thin coating of gasgitch on the individual shims of the front output shaft shim pack. Check to see if your output shafts are wiggly. Maybe they are loose or need shimming and or an out of balence driveshaft is wiping out the seals. I have also ran my vent all the way up the firewall. That way any burps can drain back down inside the reansfer case.
 

csjr

Sr. Member
Joined
Apr 18, 2007
Messages
675
Loc.
Lighthouse Point, FL
Once upon a time I had my D20 rebuilt and after all was said and done it only had the smallest of leaks/weeping from the output shaft seal. I knew it was new so I accepted it. It did not drip--at least when it was in my carport as I did not park over a drip pan. I ran straight 50W oil in the unit. I prolly could have run a 75 or 80W-90 and maybe even slowed or stopped the very slow weep, but didn't do it. I think if you had a new HD output shaft and new seals it would not leak. The gear cover should not leak nor any of the other shaft ends or shift rails. I think you could put in a seal kit yourself if you had the space and time to do it. If it's making a mess of the underside of your truck and leaving a big stain in your driveway or garage I could see pulling it--but otherwise it is just an old piece and these things happen. An Atlas-2 would stop that D20 from leaking too....:)
 
OP
OP
KS.76Sport

KS.76Sport

Sr. Member
Joined
Mar 20, 2008
Messages
354
Loc.
Wichita, KS.
Id hate to do one thing only to find a leak somewhere else. If its not something simple like the cover. Is it better just to do a tear down and re-seal from the start, applying those products and techniques you guys suggested?

Yes it is making a mess BTW. Yes an Atlas would be nice to much $$$$ for this kid.
 

broncomatt

Full Member
Joined
Dec 27, 2005
Messages
285
I did get the one in my 71 to stop for a while. The most common problem I ran into is the groves that get worn into the yokes not sealing on the gasket. There are sleeves that can be put on to help with that. When I pulled mine apart to rebuild it I was able to spend the time to properly reseal it.
 

Bronchole

Bronco Guru
Joined
Mar 24, 2004
Messages
1,611
Loc.
Chatsworth, Ca (LA)
I really wish I could get mine to seal up well. I don't mind a bit of seepage but mine is more on the drip side, probably a few dozen drips/24hours. Makes a frigging mess on the driveway (or would if I didn't park over a tarp and drip pan).

Hmmm, I wonder if the couple sealing experts could be inticed to do a "How to seal your D20" step by step. Looking at each particular leak point, discussing the variety of ways that they can be sealed with their benifits and drawbacks.
 

ugly74

Bronco abuser
Joined
Apr 17, 2006
Messages
2,856
Loc.
Colorado
I rebuilt mine with gasacinch everywhere, except for anarobic on the rear cover and shims for the front output shaft. I only have a few thousand miles on it, but so far it's still dry
 
Top