• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Should I Or Shouldn't I?? 351c

OP
OP
crab

crab

Bronco Guru
Joined
Feb 23, 2004
Messages
2,268
I heard something about drilling a 7/16 hole in in the block somewhere for better oiling?? I'll try to find the link.........anyone know what the heck I'm talking about?
As far as the motor goes. I bought a built 351w (425hp) for this project. But now that I have this Cleveland, I'm going to stick the 351w in my crawler and see what happends. I have everythig to inject the windsor so that will be another project. Right now, it has a modified holly off road carb.
So the Cleveland is going to take the place of the built windsor which I really want to have some attitude! So anyone with ideas how to make this thing 'sing', give me some advice with out going overboard.
 

Madgyver

Bronco Madman
Joined
Jul 30, 2001
Messages
15,030
crab said:
As far as the motor goes. I bought a built 351w (425hp) for this project. But now that I have this Cleveland, I'm going to stick the 351w in my crawler and see what happends. I have everythig to inject the windsor so that will be another project. Right now, it has a modified holly off road carb.
So the Cleveland is going to take the place of the built windsor which I really want to have some attitude! So anyone with ideas how to make this thing 'sing', give me some advice with out going overboard.
Did I hear "sing"? In stock form a 4V cleveland can sing add a 750 Holley DP, free flowing headers, exhaust and a healthy profile cam, she will scream!

You must go overboard and get another rig for this set-up.
That is where I'm at and it's just snowballing.......
The only butchery you'll see on my stock uncut EB would be the inner fenders only to make room for the custom Octopus looking fenderwell headers I got. I got another angled H-boost set-up to clear the big 4V cleveland heads. All I need is the time to get it all together...........
 

Quick & Dirty

Sr. Member
Joined
Feb 15, 2004
Messages
857
Another Cleveland guy here. 2 barrel block and heads, Performer intake, mild Crane cam. Makes plenty of power for street and mild off road. Didn't have to hack anything to make it fit. I did the install without dropping the tranny/tcase, so I had to beat the seam on the firewall a little, as i had to bolt the bellhousing up then drop it into the mounts, so I needed a little extra clearance to tip the engine back. I used the '80 up 351M pan which needed a few dimples to clear the diff when fully bottomed with stock bump stops. A low profile air cleaner clears the stock hood with no body lift. I had to tweak the stock throttle linkage a bit to clear, and dimple the valve cover to clear the auto column shifter linkage.
linkage.JPG
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
Madgyver said:
You must go overboard and ..........

LMAO..now that is my kind of talkin. "Why did you go so extreme?".."Because I HAD too"..LOL

If you want to go the Aussie 2V head route..we build a lot of those heads and can offer any advice for sources and mods, if asked. If you decide to go aluminum..CHI is the place to look, including for the intake to match their heads. I can hook you up with an engine and parts shop that I swap notes with that builds a lot of Pantera engines and is where the 400 (434) stroker kits come from. OR go all out like Mad says and go 4V....
 
OP
OP
crab

crab

Bronco Guru
Joined
Feb 23, 2004
Messages
2,268
What kind of numbers can I expect just with going with cam, intake and big a$$ Holley with the 2V heads? Part numbers on which ones?
 

Madgyver

Bronco Madman
Joined
Jul 30, 2001
Messages
15,030
crab said:
What kind of numbers can I expect just with going with cam, intake and big a$$ Holley with the 2V heads? Part numbers on which ones?
700 Holley DP (choke horn cut down and radiused) Demon Carbs I believe has one, 4 barrel Edelbrock intake for the 351C2V, Crower Hydraulic Hauler cam(lowest one) with matching springs and lifters (will work with stock bolt in rockers), Any free flowing exhaust which means headers also, And 4.56 gears if you have 33's.

I can't tell you numbers but by seat of pants figures this set-up is awesome!

I did my friends 82 Bronco with at 351C2V, 1850 Holley, Edelbrock intake, Crane Fireball Cam kit, and custom modified Headman headers (made to clear clutch linkage. It had a T-18, 4.11 gears and 35s. He could easily smoke the tires. That friend was so happy with his set-up that he'd refer me to his other friends for swaps which I had to turn down. My projects would never get done.
 

Bart

Bronco Guru
Joined
Dec 12, 2001
Messages
1,695
Loc.
Buffalo Gap, Texas
I have a fresh 351C long block and can't give it away. If I were you I'd pull the heads, sell the pan and pickup and use the money to build a Windsor. Ever heard of a Boss 351? It's a Windsor with Cleveland heads. 2 barrel heads are better bottom end to mid range preformers. 4 Barrel heads are strickly top end. Here's the deal. Cleveland blocks are very weak, but killer heads for breathing. Windsor blocks are bullet proof, but the heads don't breath well. Marry the two strong parts together and you have a Boss 351(vintage '69 Mustang). The change is simple with only a couple drill holes needed to match the water jackets. Then you'll have a street/sand machine that won't take a back seat to anything, even a 460. The windsor is much lighter than the Cleveland or 460, and with the c heads more powerful. If you really want to fly, get a 400 M crank and have it turned down to fit in the Windsor block. Get either 318 Chrysler connecting rods (you'll need to have them narrowed) or just get 8 Chrysler 3.9L V6 rods. Over the counter pistons can make you a 416 sbford. Put those c heads on it and you have a BOSS 416. Only draw back here is that you'll need custom built pistions. I know a company that makes adaptors to put most any sbf manifold on that block. 302, Windsor or Cleveland intakes. Go one step farther and use that 2 barrel intake with throttle body fuel injection and you'll need a pilots license :eek: I have a Windsor with all this done except for the pistons. Time will tell.
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
The Boss 351 is all Cleveland, with 4-bolt Cleveland block D1ZE. The Boss302 was the engine with big Cleveland-type heads on a 302 Windsor block...the only factory 'Clevor' so to speak.

From Ford's own specs:

351C-2V Engine Group weight - 527.52#
351W-2V Engine Group Weight - 518.40#

I don't think the 10# difference will hurt too much.. ;D
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Bart said:
I have a fresh 351C long block and can't give it away. If I were you I'd pull the heads, sell the pan and pickup and use the money to build a Windsor. Ever heard of a Boss 351? It's a Windsor with Cleveland heads. Marry the two strong parts together and you have a Boss 351(vintage '69 Mustang). If you really want to fly, get a 400 M crank and have it turned down to fit in the Windsor block. Get either 318 Chrysler connecting rods (you'll need to have them narrowed) or just get 8 Chrysler 3.9L V6 rods. Over the counter pistons can make you a 416 sbford. Put those c heads on it and you have a BOSS 416. Only draw back here is that you'll need custom built pistions. I have a Windsor with all this done except for the pistons. Time will tell.
Can you say money pit. likewise your 351W with cleveland heads(boss 351) production engine is a myth. The Boss 351 was availible in only 71 its only differance between it and 4V 351C are that it had rocker studs for adjustable rockers vs bolt on pedestals. There might be a reason you cant sell the C block.

crab
as for power to expect I'd say around 240hp flywheel with the minor mods posted torque should be higher though with the parts listed which are more low rpm oreintated I'd say 300 ft lbs or so. remember the C is a high rpm engine even with 2 barrel heads the more you can let it rev the higher the power will be. So lower gears can be a good thing to get the R's up in this engine.
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
What he said. ;D

Another little difference between the rare '71 Boss351C and the 4V that year:

330HP versus 285HP.

240HP was the stock power for the '71 351C-2V with the 9.20:1 CR It does not take much to get that to 300 without dropping a lot of coin, especially with the Aussie 2v heads bolted on. Lots of options..so much advice..LOL. Crab might just take this project off line soon.. %)
 
OP
OP
crab

crab

Bronco Guru
Joined
Feb 23, 2004
Messages
2,268
Oh, I'm still listening.........I have a radiator now so there's no turning back! Anybody have a truck pan laying around?
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
I have several..and you need the truck oil pickup assy and the main bolt with the support stud too. Figure out what you are going to do overall and shoot me a PM with your 'needs list'. We have a 'rather large' stock of Ford engine (all types) and EB/truck stuff here.
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
Great stuff Mad! Crab needs to be inspired to go outrageous with this thing. :cool:

EFI is good...Here is how we do our Cleveland EFI intakes..

DSC00839.JPG


The one shown is for a 400 but the same mod and machining setup works for the 351C too..uses the Ford injectors and fuel rails available for dirt at any yard. You can then go with an aftermarket 4V throttle body or sinmply get an elbow adapter and use the Ford throttle body and IAC assembly.
 

mountainview68

Sr. Member
Joined
Sep 5, 2004
Messages
598
Loc.
yet to be determined
crab said:
What kind of numbers can I expect just with going with cam, intake and big a$$ Holley with the 2V heads? Part numbers on which ones?

Rob, When I put together the Clevland in Ryan's Bronco we put in on the Chassis Dyno in Salem and got 190hp to the rear wheels. The dyno shop said that would equate to about 275-300 to the flywheel.

Engine had a healthy comp cam in it. 2V heads with 650 4 bbl carb, factory exhaust manifolds, C4 Auto, 4.56s, 36" swampers.
 

Desert Thrasher

Bronco Guru
Joined
Jul 14, 2001
Messages
2,353
crab said:
What kind of numbers can I expect just with going with cam, intake and big a$$ Holley with the 2V heads? Part numbers on which ones?

A few years ago I had my bronco dynoed at a local shop. It has a comp cams 255DEH grind cam, with .469 intake and .505 exhaust lift with advertised 255 intake and 263 exhaust duration. Its a mild cam but awesome for torque. An Edelbrock Performer intake with a holley 650 double pumper. I had stock exhaust manifolds with crappy exhaust and a stock type paper air filter. The heads were old and worn out, and I was running 35 inch tires with 3.50 gears.
It put over 200HP to the rear wheels and about 250 ft lbs of torque as well. The torque curve is awesome, it peaks about 2000rpm and stays flat until 5000rpm.
Now I have the heads rebuilt with larger exh valves and the Sanderson headers with nice exhaust, a K&N air filter and 4.56 gears. Id love to see what numbers she turns now.
 
Top