• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Steering cancel Cam

djanis99

New Member
Joined
Aug 21, 2020
Messages
28
I installed a new steering wheel onto my ididit column couple months ago. Steering wheel cancel has not been working since. Finally got to taking it apart today and it looks like the cancel cam is missing. The steering wheel has these two posts on the back that look like they are meant as a cancel device.

Planning to just go ahead and order a new cam unless I am missing something - see two photos below.

Thank you
 

Attachments

  • C8EB67EE-8C78-4D64-A714-E3D9A2855D47.jpeg
    C8EB67EE-8C78-4D64-A714-E3D9A2855D47.jpeg
    124.3 KB · Views: 81
  • 5D28733C-A10F-45B2-A201-D1FA9BF265EA.jpeg
    5D28733C-A10F-45B2-A201-D1FA9BF265EA.jpeg
    117.5 KB · Views: 82

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
If the wheel ever was equipped with a cancelling cam or pin, I see no evidence of it. Do you have the original? Is there room and correct diameter on the hub to install the OE cancelling cam? When buying some shiny bling, it may be a good idea to check the fit and function first.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
If the wheel ever was equipped with a cancelling cam or pin, I see no evidence of it. Do you have the original? Is there room and correct diameter on the hub to install the OE cancelling cam?
 

m_m70

Contributor
Bronco Guru
Joined
Jun 14, 2001
Messages
1,770
Loc.
Prescott AZ
I took a very small flat head screw driver and bent the pins away from the shoulder about a 16th of an inch and it works fine. Stock cancelling cam wouldn't fit on my wheel.
 

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890
I "shortened" one to fit my Lecarra steering wheel adapter.
 

Attachments

  • 20200321_124715.jpg
    20200321_124715.jpg
    67.8 KB · Views: 49

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
If you bend the pins, don't go too far. Work them a little bit at a time until they work. Pushing them too far out can be detrimental to the plastic cam follower/canceling thingy.

Paul
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Make sure the steering box is centered then install the wheel making sure the 2 pins are between the plastic cancel piece on the column. hopefully you don't have to bend the pins. overwork the plastic tips they wont last long. Maybe slid a sleeve over the pins if needed tacked in place with super glue. a thin piece of plastic tube, part of a ball point pen. roll pins are pretty hard. bending the pins could disrupt the hole they are pressed in.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
That's a great idea. Starting to think they should include some kind of sleeve material with the kits. That or go to the extra trouble of making a stepped pin. That or just make the holes and pins larger!

Paul
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
Pins were used in '78 and later turn signal switches to locate a ring in the switch. That ring includes the cancelling cams. I don't think the pins were intended to BE the cancelling cams. No surprise, they break the cancelling arms in the switch. gr8scott's fix what I used on Grant's hub adapter. It requires some grinding, but it works. As I said in post 2. Is the outer diameter correct to accept the OE cam?
 
Top