• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Stock KickDown lever help with orientation

kayakersteve

Sr. Member
Joined
May 24, 2010
Messages
882
Loc.
Western NY State
I finally put my stock kickdown lever on after sitting in the garage for over 20 years. Think I have to top correct, but doesn't look like bottom by tranny is oriented right. Here are some pics for those that would know how it should look. Thanks in advance.

Steve B
 

Attachments

  • IMG_0540[1].jpg
    IMG_0540[1].jpg
    107.4 KB · Views: 73
  • IMG_0539[1].jpg
    IMG_0539[1].jpg
    116.8 KB · Views: 77

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
It looks like the inside lever is not against the valve. Is it springy in the CCW direction?
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
When I rotate it a little clockwise, it springs back CCW

Yeah, that ain't right. You need to drop the valve body again. Unfortunately you can just turn it into position with the valve body in place.
 
OP
OP
kayakersteve

kayakersteve

Sr. Member
Joined
May 24, 2010
Messages
882
Loc.
Western NY State
OK,when I put the VB back up how will I do that different? I figured because it has spring it was engaged?? Trying to visualize how to do different
 
OP
OP
kayakersteve

kayakersteve

Sr. Member
Joined
May 24, 2010
Messages
882
Loc.
Western NY State
I also just placed Kickdown extension on as mentioned above since I had it and in picture am holding lever in a 180 degree fashion - how does that look?
 

Attachments

  • IMG_0541[1].jpg
    IMG_0541[1].jpg
    73 KB · Views: 67

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
OK,when I put the VB back up how will I do that different? I figured because it has spring it was engaged?? Trying to visualize how to do different

The end of the kickdown lever needs to go exactly where shown here. It pushes on the valve which is spring loaded. When that is positioned correctly the outside lever will be positioned correctly and you can push the valve in by turning it CCW.

You need to get it in place, then raise the valve body, then test the kickdown to make sure it's still in place, and make sure the manual lever is in place before bolting it up.
 

Attachments

  • Bronco 015 small.jpg
    Bronco 015 small.jpg
    103.1 KB · Views: 58

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
I also just placed Kickdown extension on as mentioned above since I had it and in picture am holding lever in a 180 degree fashion - how does that look?

The orientation was correct in your 1st pic, just 80 degrees too far CW because the inside lever isn't against the valve.
 
OP
OP
kayakersteve

kayakersteve

Sr. Member
Joined
May 24, 2010
Messages
882
Loc.
Western NY State
Ok - I will go back in tomorrow morning. The thing I struggle with is what is causing any spring pressure if I am not on the end of the rod?
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
If you try to force it too much you could spin the lever on the shaft. It's just pressed on. BTW, did you find the old lever inside?
 
OP
OP
kayakersteve

kayakersteve

Sr. Member
Joined
May 24, 2010
Messages
882
Loc.
Western NY State
OK, Think I got it this time......

First pic shows how the kick down shaft was oriented in the tranny - YOU WERE RIGHT Viperwolf! Anyhow, with the help of a third hand I got it to work and the second picture shows the orientation
 

Attachments

  • IMG_0544[1].jpg
    IMG_0544[1].jpg
    114.4 KB · Views: 40
  • IMG_0545[1].jpg
    IMG_0545[1].jpg
    87.3 KB · Views: 39
Top