• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Superduty hydroboost install/fittings confirmation

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
1999 Ford Superduty HB
1985 Dodge Diplomat MC
4x4x2 steering box
Saginaw pump
3/16” firewall braket
½” spacer

I have searched multiple threads only to come up with multiple answers to my questions. This is my daily driver so I want to source all of the parts before I start so I’m only down for a few days. If that is even possible. My HB, Box, and Pump did not come with any fittings.

**update**
5C22F5BC-D506-42C0-89E2-071C554B1DE5-2370-000002E1BABB77C3.jpg


Parts_zps4f1c7049.jpg


hydroboostdiagram2_zps0e630afc.jpg

Hydroboost
High pressure outlet. 16mm x 1.5 to -6AN FBM2608
High pressure inlet. 18mm x 1.5 to -6AN FBM2609
Return line to pump. Stock fitting

4x4x2 Box
High pressure inlet. 1/2-20" to -6AN FBM2963
Return line to cooler. 5/8-18” to -6AN FBM2964

Saginaw Pump
High pressure outlet. 5/8-18” to -6AN FBM2964

Does it look like I’m on the right track as far as fittings? I know I’ll need some 90* and 45*-6AN elbows and I’ll need to figure out how to make the lines. I would like to place one order to Summit this week so I need to get an inventory of everything I’ll need.

Thanks
 
Last edited:

SC74

Contributor
Bronco Guru
Joined
May 24, 2004
Messages
3,472
What is the reasoning behind the 1985 Dodge Diplomat MC?
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
What is the reasoning behind the 1985 Dodge Diplomat MC?

That was my SWAG. After reading lots of threads and posts about master cylinder size and how it affected hydroboost pedal feel and travel, I decided that my first try would be 1 1/16" bore MC. I looked on the very old Hydratech Braking web site, when it still listed specifics of various master cylinders. The Dodge master cylinder looked interesting for a couple reasons. One, it had the 1 1/16" bore. Two, it was the newer style aluminum with a plastic reservoir. And three, it had the same bolt spacing as the Ford Hydroboost. When I got both pieces, I found that the rod on the SD hydroboost was exactly 1/2" too long, which worked out OK, since I had to turn the booster 90° to make it fit. Made the 1/2" aluminum spacer to accomplish that.

I couldn't be happier with the pedal feel and action/reaction of the hydroboost.
 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
I think the 4x4x2 size is wrong. There are 2 fittings on it (different sizes)

1/2-20 inverted flare inlet
5/8-18 inveted flare return

Source- http://www.wcb4x4.com/tech/diyrockcrawler.shtml

Thank you for the link. I've looked at that numerous times and didn't catch that. I did a few google searches to come up with the fittings needed and obviously I got the wrong info.

*I updated my original post and picture to reflect the changes

Not sure how much difference from 1997 to 1999 but here's mine


1997 Powerstroke Hydroboost (Used)

11/16" to -6 AN fitting (HB)

5/8" to -6 AN fitting (HB)

http://www.emotoman.com/4x4/hydroboost/hydroboost.html

Your tech article is the one that made me decide on the Superduty HB setup. When I decided I wanted to order the fittings and make the hose myself, I started reading other peoples setups to make sure I got the correct fittings for a 99 HB. That is when I read they were metric fittings.

Steve asked the same question in this thread and that is where I got the info.
http://classicbroncos.com/forums/showthread.php?t=106210&highlight=superduty

Here is another thread with conflicting info
http://www.classicbroncos.com/forums/showthread.php?t=95720
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
When I decided I wanted to order the fittings and make the hose myself, I started reading other peoples setups to make sure I got the correct fittings for a 99 HB. That is when I read they were metric fittings.
Dunno if it makes a difference to you. But, motoman paid probably twice what I paid for the hoses. I got mine done at a local hose/hydraulic shop using JIC fittings. motoman went to the Parker store and got AN fittings, and shiny and/or blue hose.
 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
Dunno if it makes a difference to you. But, motoman paid probably twice what I paid for the hoses. I got mine done at a local hose/hydraulic shop using JIC fittings. motoman went to the Parker store and got AN fittings, and shiny and/or blue hose.

The only reason I'm thinking of doing it myself is so I can get the hoses the correct length. I do not want extra length hose to mess around with when I'm finished. I'm sure I could take some rough measurments and get it close before I went into the hydraulic shop.

Were yours metric or standard?
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
Were yours metric or standard?

Metric, but I bought adapters to convert to -6 JIC/AN.

The hydraulic shop isn't too far from my house. When I first went there, of course there's lots of choices of which fitting to use to make it all pretty. The guys there worked with me, and let me take a pile of different fittings home to see which would work best at which location. All they did was make a list of what I took. I took rough measurements of how long each hose needed to be. They crimped on one end so I could mark the hose to the correct length, and to "clock" the fitting on the hose, since both ends were 90°s. It took me a couple trips to the shop, but the results were very nice, and all three hoses (two pressure hoses, and I got an end crimped on the low pressure return hose, just for looks) only cost me $72.

This same shop only charged me $20 to silver-braze a JIC fitting on my PS pump housing to make it a dual return pump.
 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
Metric, but I bought adapters to convert to -6 JIC/AN.

The hydraulic shop isn't too far from my house. When I first went there, of course there's lots of choices of which fitting to use to make it all pretty. The guys there worked with me, and let me take a pile of different fittings home to see which would work best at which location. All they did was make a list of what I took. I took rough measurements of how long each hose needed to be. They crimped on one end so I could mark the hose to the correct length, and to "clock" the fitting on the hose, since both ends were 90°s. It took me a couple trips to the shop, but the results were very nice, and all three hoses (two pressure hoses, and I got an end crimped on the low pressure return hose, just for looks) only cost me $72.

This same shop only charged me $20 to silver-braze a JIC fitting on my PS pump housing to make it a dual return pump.

What year Superduty HB do you have? Greg's 97 has standard fittings and yours has metric. Wonder what mine will have.

I can go into the haudralic shop to see what they can do for me. I don't mind saving some money.
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
What year Superduty HB do you have? Greg's 97 has standard fittings and yours has metric. Wonder what mine will have.

I can go into the haudralic shop to see what they can do for me. I don't mind saving some money.
2000.

I like saving money. Lets me buy more Bronco parts...
 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
2000.

I like saving money. Lets me buy more Bronco parts...

I think 99-2000 are the same so I'll look into metric. I have lots of other things to buy so I'll try to save some money :)
 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
Steve - Do you know what size adapter I would need for the return hose?
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
Do you know what size adapter I would need for the return hose?

If your booster's complete, you'll have a fitting for the low pressure return line on it. Slip your low pressure hose over it, add a hose clamp, and you're done. That's the low $$ solution and it works fine.

If you want to coordinate things and add a -6 fitting, you'll need P/N HBS9101 from Hydratech:

http://www.hydratechbraking.com/hose_fittings.html

Todd Z.
 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
If your booster's complete, you'll have a fitting for the low pressure return line on it. Slip your low pressure hose over it, add a hose clamp, and you're done. That's the low $$ solution and it works fine.

If you want to coordinate things and add a -6 fitting, you'll need P/N HBS9101 from Hydratech:

http://www.hydratechbraking.com/hose_fittings.html

Todd Z.

I just looked again and my HB does have the fitting for the return line so I'll use that.

Thanks for all the help. If all my fittings look correct, I'm going to place my order soon.
 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
Now that I have the correct fittings for my HB setup I want to make sure I'm using the correct type of hose and hose ends. There are lots of options on Summit and when you don't know what you're doing it can get overwhelming.

I think this is the method I want to use.
http://www.hydratechbraking.com/hosetech.html

Aeroquip TFE Racing Hose AER-FCC0610

Aeroquip reusable hose ends 45* AER-FBM1112 90* AER-FBM1122

All of these fittings and hose ends are steel. Is there a preference between steel and aluminum?
 
Top