• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Tapping lifter

red67

Sr. Member
Joined
Sep 4, 2001
Messages
423
Loc.
Austin Texas
How do I get my lifter to stop tapping:mad: ?:? At least I am pretty sure it is a lifter. At first I thought it was an exhaust leak (thats what it sounds like; i ve never had a tapping lifter before), but on closer examination, Im pretty sure it is coming from inside the valve cover. Anyway, my dad just put on a new exhaust system (twin flowmaster delta 50s;D ) and it was sounding good, now my car sounds like a POS with this tapping. Ive never really done any work with heads (read:no Experience), so this is new to me. Can somebody tell me how to get this to stop?:? %)

TIA

Ryan:'(
 

BwoncoHowie

C-4 Wizard
Joined
Nov 11, 2002
Messages
3,571
If its out of adjustment;
You will need to remove the valve cover and check it. Then adjust as necessary.

If the lifter is varnished;
I have un froze sticky lifters by running a quart of ATF in the crankcase for about 800 mi before an oil change, or just change out the oil after the noise stops. 1 Qt. of Marvel Mystery oil works much faster but it is more expensive. If you have a lot of gunk and sluge deposits inside your motor you may need to change the oil sooner (about 400mi then repeat the process) because all the crap usually ends up in the oil filter

just a couple of things that have worked for me on several occasions.
 

Bronco Sport

Bronco Guru
Joined
Jul 29, 2003
Messages
1,568
Loc.
NW Portland, Oregon
I had the same problem last summer. It started slowly and go worse. It tried the add in stuff to my oil but that was a no go. It just got worse. I ended up replacing all of my lifters and have had no problems since. They are cheap and very easy to replace.
 

kwspony

Bronco Guru
Joined
Apr 28, 2003
Messages
1,114
Loc.
Roseville
which lifter is tapping? I have one that taps alot too. It's number 8 cylinder. Started tapping not long after the engine was rebuilt. I think it's because the older blocks have larger oil passages or something so it may not be getting full pressure. I am planning on installing a high volume oil pump soon hoping that will take care of it. Just something to think about. I have tried ATF and it didn't help in my situation so I think mine needs alittle more volume.
 
OP
OP
red67

red67

Sr. Member
Joined
Sep 4, 2001
Messages
423
Loc.
Austin Texas
BwoncoHowie said:
If its out of adjustment;
You will need to remove the valve cover and check it. Then adjust as necessary.

I know I don't have "gunk" inside, cause we pulled the valve covers off recently and it was pretty clean inside. BUT how do I "adjust as necessary"??:?
 

Bronco Sport

Bronco Guru
Joined
Jul 29, 2003
Messages
1,568
Loc.
NW Portland, Oregon
red67 said:
I know I don't have "gunk" inside, cause we pulled the valve covers off recently and it was pretty clean inside. BUT how do I "adjust as necessary"??:?

Take the valve cover off and start the engine. A good idea is to put something over the exhaust manifold to keep the shooting oil off the manifold. Then adjust the top bolt at the rocker until it stops knocking. You just want to make sure not to over tighten it. If you do you can bend a push rod or wear the cam.
 
OP
OP
red67

red67

Sr. Member
Joined
Sep 4, 2001
Messages
423
Loc.
Austin Texas
Bronco Sport said:
Take the valve cover off and start the engine. A good idea is to put something over the exhaust manifold to keep the shooting oil off the manifold. Then adjust the top bolt at the rocker until it stops knocking. You just want to make sure not to over tighten it. If you do you can bend a push rod or wear the cam.

Thank you very much;D
 

67ster

Bronco Guru
Joined
Feb 18, 2002
Messages
1,572
My little 289 has always had a lifter tick on a cold start up but it clears up immediatly when the oil pressure comes up . I replaced the cam , lifters and pushrods in about 1980 on the advice of a Ford mechanic that told me they had some faulty parts come through on the early engines . It didn't make any difference. I change oil often using a good 10-30 brand .
 

66horse

Bronco Guru
Joined
Jan 7, 2002
Messages
3,394
NOt sure if yours is just at startup or not buthere is one for you.... My buddy had a lifter tap... cahnged from Fram to purolator filter and it went away....
 

mtkawboy

Bronco Guru
Joined
Jan 28, 2004
Messages
1,525
Loc.
Billings Mt
Not all Bronco lifters are adjustable. If the valve end tip of the rocker arm is flat they are , if its U shaped they arent. Marvel Mystery oil is the truth. If it dont fix it replace them. Got to keep the oil changed too.
 

Mr Joe

Bronco Guru
Joined
Dec 2, 2003
Messages
2,212
The engine cleaning tricks work only if the lifter wasn't tapping forever. After a while, only replacement will correct it. Also, noisey lifters can be the result of oil pressure problems. Make sure you're running good oil pressure before just fixing a lifter....
 
OP
OP
red67

red67

Sr. Member
Joined
Sep 4, 2001
Messages
423
Loc.
Austin Texas
The problem just started yesterday. Im on Spring BReak and came back home to SO Cal. My GF and another buddy came down as well. WE have been putting about 100+ miles everyday on my EB since last sunday looking at everything down here as well as soaking up the sun. ;D
Well, i took off the valve cover and made sure everything was tight. And it still taps:mad: My pop said that it could be a valve. He hasnt had time to help me because today my sister burned up the tranny in her Camary%) . Anyway he told me to pour some ATF down the carb while its running to see if I can 'unstick' it. I havnt had a chance to do this because I guess it makes alot of smoke doing this, and we live in a kinda nice neighborhood. I did pour some 'oil detergent' in the oil, and then drove bout 25 miles, but the tapping still exists. SO......?:? %)

THen somebody stopped me and wanted to know how much I wanted for my truck...............................:eek: , but I told em it wasnt for sale;D
 

hackyrat

Sr. Member
Joined
May 25, 2002
Messages
565
Just in case, check to see if you have a loose spark plug. I had a loose plug on the wifes car and it tapped like a lifter at low RPM. Easy check and might get lucky.
 

wildbill

Old Bronco Guy
Joined
Jun 29, 2001
Messages
6,890
;D ;D ;D Take the valve cover off and put a strate edge and see if you dont have a stud comeing out it will cause a lifter to tick. If you do just replace it and you should be good to go good luck.;D ;D ;D Bill :cool: %) :p
 
OP
OP
red67

red67

Sr. Member
Joined
Sep 4, 2001
Messages
423
Loc.
Austin Texas
hackyrat said:
Just in case, check to see if you have a loose spark plug. I had a loose plug on the wifes car and it tapped like a lifter at low RPM. Easy check and might get lucky.

I ve had that happen before and that is what I thought it was, but it wasnt:mad:

wildbill said:
Take the valve cover off and put a strate edge and see if you dont have a stud comeing out it will cause a lifter to tick. If you do just replace it and you should be good to go good luck.

Yeah, that looks like what I am gonna try later today. I fly back to cold-ass MI tomorrow to finish up the semester, so I might have to wait till the summer to get er fixed.

71sport408 said:
Check your rocker arms also, as hinted on before, to make sure none of them are loose.
Willdoer. thanks guys


ryan
 
Top