• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Third times a charm v3.0

OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
Little progress today. Cut out the almost new exhaust to make room for the frame side link mounts and tacked the Artec brackets together. I'm going to see what my link numbers look like with these mounts and then the more traditional style frame mounts.



 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
All the parts for the axle builds have been purchased. Everything will be basically new except for the housings and the front shafts. I will upgrade the RCVs soon.

1976 F150 High Pinion Dana 44
-ARB
-Yukon 5.13 gears, Master overhaul kit, Ball Joints
-Spicer u-joints
-Wild Horses spindle bushings
-Timken axle bearings and seals
-Warn premium hubs
-RuffStuff diff cover
-Raybestos loaded calipers and rotors

1976 F150 9 inch
-ARB, 35 spline
-Yukon 35 spline shafts w/ SET20 bearings and Yukon bearing retainers
-Yukon 5.13 gears, Master overhaul kit
-Yukon 3.25" Nodular iron dropout with forged caps
-Yukon forged 1350 u joint
-Daytona pinion support
-RuffStuff pinion guard and rear truss
-Artec top truss for the upper link brackets
-Raybestos loaded calipers and rotors w/ Speedway caliper brackets
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
Cool build.

Let us know how you like that RuffStuff back brace...I put one on my F150 9" and it was almost more work than if I'd made it myself. After tweaking and fighting it for hours, I finally just cut the bends and installed it as 3-pieces...way easier. I should have just done it from the start, but chopping up new parts just so you can weld them back together seemed silly to me (at first anyway).
 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
Cool build.

Let us know how you like that RuffStuff back brace...I put one on my F150 9" and it was almost more work than if I'd made it myself. After tweaking and fighting it for hours, I finally just cut the bends and installed it as 3-pieces...way easier. I should have just done it from the start, but chopping up new parts just so you can weld them back together seemed silly to me (at first anyway).

I figured I would have to do some cutting and welding to get it to fit around the Artec top truss. I hope it's not bad.
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
I figured I would have to do some cutting and welding to get it to fit around the Artec top truss. I hope it's not bad.

Are you planning on replacing the housing ends? If not, you may want to consider it as it will allow you to account for any distortion in the housing due to all of the truss work you're doing. FWIW, I ran an alignment bar through mine prior to welding and it wasn't straight to begin with, so putting new ends on aligned everything and gave me new, tight bearing counterbores.
 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
Are you planning on replacing the housing ends? If not, you may want to consider it as it will allow you to account for any distortion in the housing due to all of the truss work you're doing. FWIW, I ran an alignment bar through mine prior to welding and it wasn't straight to begin with, so putting new ends on aligned everything and gave me new, tight bearing counterbores.

I hadn't thought of that issue. I know I need to be careful, but if it's going to warp anyway, I guess the new ends will be necessary. I

Dual shock hoops?

No, ORI struts front and rear.
 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
If this housing is warped when I'm done, I'll have to buy the RuffStuff housing ;D:cool:
 

badmuttstang

redneck grease monkey
Joined
Oct 25, 2009
Messages
2,807
I like that idea Jaromy, I think I'm going to start off there with mine but with everything you just bought and still need to get I'm sure it's one of those things that has to be justified. ;D
 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
I like that idea Jaromy, I think I'm going to start off there with mine but with everything you just bought and still need to get I'm sure it's one of those things that has to be justified. ;D

Yeah, I just don't think I'm there yet. If I end up needing it, I will purchase. I'm hoping I don't need it right away because I still have a few large purchases to make.
 

badmuttstang

redneck grease monkey
Joined
Oct 25, 2009
Messages
2,807
Yeah I think those seats might be one of the big ticket items but that's just me. Gotta keep the wife happy;D
 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
Yeah I think those seats might be one of the big ticket items but that's just me. Gotta keep the wife happy;D

I think those are off the list in this round 😂

Last few parts for the axle builds arrived today.

 

badmuttstang

redneck grease monkey
Joined
Oct 25, 2009
Messages
2,807
Sweet starting to rack up a pile of parts just like I have now both of us just need to start putting them on.:cool:
 
Top