• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

TIG welding tips?

NicksTrix

Bronco Guru
Joined
Aug 1, 2001
Messages
6,410
dave, for that .120 wall i'd think about stepping up to 3/32 tungsten. you could try a .045 filler rod as well.
a gas lense and a # 6 -8 cup are the usual standard on my torch. i usually run a bit more flow, i found 15-17 is a good base for me. that works for the various angles i get into.
the inverter machines are sweet, someday i'd love to get back to a miller dynasty 300 like i used when i worked at the engine shop. the pulse feature is quite nice and you can really dial in some programs with time. until then i'm stuck with my transformer syncrowave 250 tig runner.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Another tip
Don't touch the filler rod with the tungsten as you touch the pedal and iniciate the HF start. That HF start will go up the filler rod and through your glove and leave a nice hard burn/crater in your hand that will take a week or two to heal up. Hurts WAY MORE then any ignition coil jolt I have ever had. And I can tell you that an MSD really does fire 6 times as I could count each hit (my worst ignition coil shock when the distributor was bumped and the key was on and the coil wire was off the distributor and against my arm)

But a much prefer the HF arc into the hand compared to being skewered by a skipped out, white hot MIG wire through the index finger. That scar will be there for years.
 

Dave

Contributor
Bronco Guru
Joined
Aug 25, 2006
Messages
2,264
I was welding with HF a while back in the garage. About 6 foot straight above in the livingroom were the lap top and DVR. The lap top crashed and wouldn't reboot. Had to reload the entire system. The DVR got scrambled and had to be replaced (by Comcast). Could have been a coinsidence but ...
 
OP
OP
Madgyver

Madgyver

Bronco Madman
Joined
Jul 30, 2001
Messages
15,030
That's the answers that I'm looking for... various set-ups to play with..
 

Dave

Contributor
Bronco Guru
Joined
Aug 25, 2006
Messages
2,264
Check out "Gas Tungsten Arc Welding Handbook" by William H. Minnick. It was the text book for a commy college class that I was going to take before a buddy told me that the "professor" was just going to read the book to us for $1200.

It has a lot of setups, techniques, and processes for the various metals. One thing that I learned from the Covell DVD was to keep the rod within the gas protection between stabs and at the post flow.
 
OP
OP
Madgyver

Madgyver

Bronco Madman
Joined
Jul 30, 2001
Messages
15,030
I have that book..
Well, Here is the main part of the pipe rack I cheated on, Used CO2 instead of argon. I still need to build the removable rear rails. Just got it on the new 3500 Chevy Utility that I use for work. I do miss the 3500 Dually that I had before it, I quess it grew on me.
 

Attachments

  • DSC05516.jpg
    DSC05516.jpg
    89.3 KB · Views: 24

Dave

Contributor
Bronco Guru
Joined
Aug 25, 2006
Messages
2,264
I have that book..
Well, Here is the main part of the pipe rack I cheated on, Used CO2 instead of argon. I still need to build the removable rear rails. Just got it on the new 3500 Chevy Utility that I use for work. I do miss the 3500 Dually that I had before it, I quess it grew on me.

Wow, CO2 works? Hard to imagin after after the results I got with a mismarked tank of argon/CO2 mix. Learn something new each day.
 
OP
OP
Madgyver

Madgyver

Bronco Madman
Joined
Jul 30, 2001
Messages
15,030
Wow, CO2 works? Hard to imagin after after the results I got with a mismarked tank of argon/CO2 mix. Learn something new each day.

well, It did and it didn't.
Welds didn't come out that great and I went through a few tungstens but it got the job done and I didn't use any of MY argon.
Everything else the Co. paid for.
 
Top