• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Tire help quick please

74BroncoCO

Bronco Guru
Joined
Nov 3, 2004
Messages
2,378
I have a lead on a set of brand new 35x12.5r15 MTR's for $800 from a private seller. I am going to get MTR's anyway, but I am wondering if anyone has ever seen a MTR blowout or pinch or otherwise destroy itself on a rock, tree...

I have connections through a tire store and can get those tires for $760 + tax + road hazard for a total of around $920. Is it worth the road hazzard to buy them through the store or should I just buy them from the private seller since they are tough tires?? Thanks for your opinion!

J.D.
 

Socal Tom

Bronco Guru
Joined
Feb 12, 2004
Messages
2,442
Loc.
San Diego, CA
Any tire can and will get a hole in it if the terrain is right.
MTRs hold up pretty well. Most people think they hold up better than the BFG MTs. Some tire stores will sell you a warranty even if you bought the tires somewhere else.
Tom
 
OP
OP
7

74BroncoCO

Bronco Guru
Joined
Nov 3, 2004
Messages
2,378
Socal Tom said:
Some tire stores will sell you a warranty even if you bought the tires somewhere else.
Tom

That's a thought, although if tax was less than $40, then that would cost me more since I can get the tires for $760 at the store.

I am leaning toward taking the risk and saving the $120 for something else. Plus I have good spares!

J.D.
 
OP
OP
7

74BroncoCO

Bronco Guru
Joined
Nov 3, 2004
Messages
2,378
He just dropped the price $100, so I said I'd take them. And he's meeting me less than 6 miles from my house! He really wants some cash before this weekend. I'll put the money saved aside if I have trouble later!

J.D.
 

68 Broncoholic

Bronco Guru
Joined
May 16, 2005
Messages
1,742
Loc.
WA
If you can get the unconditional warrantee so if off road you blow the sidewall its covered. My buddy blew a sidewall which popped the tire off the bead before he could stop on flat ground to change it. By that time the tire got chewed up and lots of mud packed inside. The tire store didn't replace or give money towards another due to the circumstances.
I personally don't like the tire, only good on dry dirt, rocks and street. Mud packs in them and acts like slicks.
 
OP
OP
7

74BroncoCO

Bronco Guru
Joined
Nov 3, 2004
Messages
2,378
I think discount tire's warranty does cover just about anything, but I'll just be careful or obstacles that could damage the tire. I don't care for mud much anyway. It gets past seals and causes damage. I'm having a hard time keeping oil in my front pumpkin. Even after I just replaced that darn inner axle seal. :mad:

J.D.
 

68 Broncoholic

Bronco Guru
Joined
May 16, 2005
Messages
1,742
Loc.
WA
I hope you replaced both inner axle seals. Do you see where its leaking from?
Wonder if the axle shaft is bent causing the seal to leak. If it lobes around it will cause a leak.
 
OP
OP
7

74BroncoCO

Bronco Guru
Joined
Nov 3, 2004
Messages
2,378
Yeah I replaced both even though the passenger side wasn't leaking. It's just such a pain in the rear job to do that I am dreading doing it again. I was sorta wondering if the shaft was bent myself. When I do the job, I'll pull the shaft all the way out and see if it's bent. Until then, I stay away from water and mud.

J.D.
 

68 Broncoholic

Bronco Guru
Joined
May 16, 2005
Messages
1,742
Loc.
WA
could be that the new seal you put in got damaged while sliding in the axle shaft. Or the seal wasn't put in perfectly straight causing it to oval out and leak.
 
OP
OP
7

74BroncoCO

Bronco Guru
Joined
Nov 3, 2004
Messages
2,378
Yeah, when I get to that point again, I am going to see if I can guide the shaft in while my wife pushes it. It should be straight, I used a peice of 2" tubing and it fit perfectly in the seal. I am also going to use a liberal amount of anarheobic (sp) silicon on the mounting surface of the seal in case. If I am setting level, I have no trouble, but when it's leaning on a rock, then I notice it ooze a little. The worst part is having to remove both hubs to get the one seal since the carrier has to be dropped. But it's an opportunity to become more familiar with my bronco.

J.D.
 
Top