• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Torker 289

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
While it's quite normal for the plate to be a little flexy like that, you can clearly see that the interface (either the pin or the hole) between the plate and the vacuum advance arm is worn pretty good. Lots of slop there.

Should not effect the overall installation at the moment, but definitely indicates wear and tear and should be dealt with to get the most stable timing you can.
And that's really what deteriorates in a distributor anyway. All the mechanical aspects. Bearings and bushings and shafts and gears and pins and springs and holes and things.
Each one adds up to more and more inconsistency in the spark.

You might pop the clip off (carefully!) to see if it's the arm or the pin that is most worn out. If it's the arm, you can replace it with a new vacuum advance canister which should have a new arm on it.
If the pin is worn, a new plate is needed.

I thought the Ignitor came with it's own "points plate" as part of the assembly? I'm guessing not though, since it looks like you're using the old plate to attach things to.

Paul
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
Paul my friend you are dead on yet again. Vacuum advance arm was practically an oval. Got a new one arriving tomorrow. Thanks!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Cool. Should be nice and tight after that.
That's actually one of those things that used to make the difference between a stock distributor replacement and a fancy high-zoot (big buck) custom distributor.
The holes like that would have bronze bushings in them, the upper bushings would be replaced by sealed bearings, advance weights would pivot on bronze bushings too.
Took time and money to put that stuff in there, so most would just buy a regular distributor.

The good news is that even a stock one will last a long time. And even longer if kept clean and maybe even lubed if you can do it without hurting the electronics.
Maybe my friend that used to regularly squirt WD40 inside his wasn't so crazy after all...:cool:

Paul
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
Replaced the vacuum can. Definitely improved but still some movement in there. I bet its a bushing. What kind of bushings should be in there?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Not sure there ever was a bushing between the plate and the vacuum arm. But a little slop is not a bad thing necessarily. Stays working longer with a little tolerance, as long as it's not too much. What you had before was too much.
How much did the new part reduce it? By more than half? If so you might be in the green again.

You could always make a custom bronze bushing, but being so small I think that would be a major pain and likely take more time than it's worth unless you're well equipped in the machine tool department. For sure it would cost more to have someone do it than a new distributor would cost!

Paul
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
I would say probably less than half. Enough for me to hopefully move on to the next thing. It fires right up, idles great. However if I'm just idling in neutral and Rev it, it's smooth smooth smooth, until mid rpm range where it hesitates, sputters, catches itself, and then screams and revs up as it should. I want to say it's leaning out and then catching itself? Bought a rebuild kit for the carb so I'm gonna try that. Timing is set at about 12 degrees. Played with the timing and that's where it likes it best although it doesn't really run great anywhere. Let's say it runs the least bad at 12 degrees haha. Of course this could be timing or a carb issue, but I'm sick of playing with the dizzy so I'm gonna try the carb lol.
 

EB70

Sr. Member
Joined
Jun 9, 2006
Messages
730
Sounds like you are getting there with the tuning. I do have some experience with that intake. I pulled a strong 302 out of a 69 Bronco (which did have a scoop to clear the intake BTW) and put it in my old car.

Pulls strong, real strong. However, unless you are sand dragging, it is a less than stellar intake for a 4x4 IMHO. Even in the car low-end torque is bad. But once its up and going it is pretty snappy.

Also, it is quite cold blooded and so forth. Nice intake for a properly set up performance engine with the supports needed. Not a good one for a typical 4x4 in my opinion.
 
Top