• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Totally Stainless

chriswitt

Full Member
Joined
Nov 26, 2009
Messages
191
Many of the Bolts that I am replacing with Totally Stainless bolts were Grade 5 OEM bolts. I know that SS is softer. What do you guys think in areas like Hood Bolts, Tail Gate Bolts, Power Brake Booster bolts.... Is the SS strong enough?
 

johnnybgood74

Bronco Guru
Joined
Mar 4, 2009
Messages
1,135
Loc.
boise, idaho
Chris, i think you will be just fine using SS bolts in all the areas that you have stated. they will definately be strong enough
 

miikee73

Shadetree Guru
Joined
Dec 14, 2010
Messages
3,551
Loc.
Aloha
All I can add is use some type of anti-seize. Once they seize they are a bitch!
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
This stuff helps keep stainless from gauling. I even use it on my guns.
 

Attachments

  • MS-TL-BGT.jpg
    MS-TL-BGT.jpg
    10 KB · Views: 54

patterdale

Bronco Guru
Joined
May 24, 2010
Messages
1,252
Many of the Bolts that I am replacing with Totally Stainless bolts were Grade 5 OEM bolts. I know that SS is softer. What do you guys think in areas like Hood Bolts, Tail Gate Bolts, Power Brake Booster bolts.... Is the SS strong enough?

Putting dissimilar metals together causes galvanic corrosion. Just ask the Maytag repairman. Years ago they put some stainless parts on a steel shaft and after years of use the two were inseparable. Made it so it was cheaper to buy a new washer than replace the parts. Strength wise you should be okay but use the antisieze or it will be even more work to get things apart in the long run. If you are in an area of the country that uses salt in the winter the problem could be magnified.
 

Crawdad

Bronco Guru
Joined
Feb 16, 2011
Messages
3,635
SS is much stronger than mild steel bolts, and a lot more expensive. If you are using SS nuts then dont waste your anti-seize. But if you are using factory nuts with SS bolts then yes do use it.
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
SS is much stronger than mild steel bolts, and a lot more expensive. If you are using SS nuts then dont waste your anti-seize. But if you are using factory nuts with SS bolts then yes do use it.

Stainless on stainless will gaul quicker than stainless and mild steel. If you use stainless you use anti-seize.
 

71broncman

Sr. Member
Joined
Sep 6, 2009
Messages
410
Loc.
Maysville, Ky
Stainless on stainless will gaul quicker than stainless and mild steel. If you use stainless you use anti-seize.

X 3 or 4 on that. From my experience with SS bolts at work when the stainless nut gauls to a stainless bolt theonly way to get them apart is to either break the bolt or cut it if you can get to it. Also, SS bolts have about the same tensile strength as a grade 5 bolt of the same size.
Mark.
 

johnnybgood74

Bronco Guru
Joined
Mar 4, 2009
Messages
1,135
Loc.
boise, idaho
oh man does stainless on stainless gaul on themselves!!!!! i used to build swimming pools for a living, we used stainless studs that we poured in our concrete for the diving board jig. we then used the supplied hardware which was SS washers and nuts. i got them on about half way and they froze up solid! i couldnt budge them in either direction! had to jack hammer out the section of concrete and pour in a new jig. they dont use SS hardware for the jigs anymore. to many complaints from customers!
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
The world has gone stainless crazy. There are more downsides than positives when using it on cars. Also there is a lot more junk imported stainless hardware on the market these days. I'll use good carbon steel wherever I can.
 

trailpsycho

Bronco Guru
Joined
Dec 11, 2003
Messages
4,856
I bought the TS complete indented hex kit for my build. I must say that it is the nicest SS hardware I have seen, used. Thick washers, very good quality. Its not cheap. Ultimately, if you are not doing a 'stock' rebuild, there is alot of hardware that you will not use...at least for the designated purpose. I used most of mine here and there. The fender kits, door kits and such are nice. Did I mention how nice the 5/16" washers were?? Seriously, I havent found anything comparable at any local store. Definitely use the anti-seize.
 

Tuck

Sr. Member
Joined
Jul 25, 2001
Messages
947
I have a lot of SS hardware also & am not concerned about breakage (until something breaks). Absolutely true about galvanic corrosion...big problem on aircraft too. I tend to overkill, but there's hardly a bolt on my builb that DOESN'T get anti-sieze, SS or not.
 
Top