• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Trick Flow High Port Heads - Header Issues?

86Horn_EB_77

Jr. Member
Joined
Aug 31, 2006
Messages
100
Loc.
Austin
Found a deal on some Trick Flow High port heads - they have two sets of header bolts per exhaust port. Good deal but worried that these are only good for go-fast Mustang Boys.

Planning to use these on a 331 stroker with BC Broncos headers.

Worried that none of the Bronco vendor headers are designed for "high port" small block heads.

Running an auto so don't need to clear a clutch linkage. (AOD first, then 4R70W). EFI with Edelbrock RPM II or ported GT40 upper/lower

2.05 intakes/60cc chambers - planning to use with a -4cc piston

So - will any Bronco headers fit?
Any other glaring reason not to use these heads?

Will be mostly a street bronco but I'd still like it to have decent torque. Haven't picked the cam yet. This engine might see a blower some day so don't want to go too high on the CR. Not a daily driver so don't mind running 93 Octane in it.

Thoughts people?
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
60cc bowls with only a 4cc dish piston....what kind of jet fuel are you going to use? :) -- just asking, what is your static compr. ratio?. Your BC headers will work...what inch body lift ?
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
You would probably only have issues with full length headers. BC and WH both sell a short header that would likely be fine. I hear that BC's are really nice. I'm still using 27 year old chrome Duffys.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Shouldnt be any major issues if the headers fit a 351W in a bronco then they will fit your high port heads.. I'd defitnetly want to run 1 5/8 in headers with those heads.
 
OP
OP
86Horn_EB_77

86Horn_EB_77

Jr. Member
Joined
Aug 31, 2006
Messages
100
Loc.
Austin
nvrstuk - 1 inch body lift

And yes I'm definately looking for headers with 1 5/8" primaries. Thus the plan to use the BC headers.

I am NOT a small block Ford guy by background - so YES, I need help calculating the CR - I'm guessing that a 60cc chamber ain't exactly big if I'm running -4cc pistons? Can I use an extra thick head gasket to lower the CR a bit? Would like to be at 9.5 max. Summit has an online CR calculator - but they want the head gasket thickness and I have no idea... Would like to run 93 Octane - those barrels of VP 112 can get expensive...:)

Alot of the aftermarket heads seem to have 60cc chambers (or even 58cc). Would I be better off finding some 62 or 64cc heads? I found some Iron Windsor Sr's with 64cc chambers but I really want to use Aluminum heads.

More feedback Fellas? Cam ideas appreciated too.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
Here's my specs and I'm close to the CR you want and I dialed it in for crappy 87octane Canadian/NW Territory gas....
64cc Trick Flow 205 cc heads
22cc dish pistons
.040" gasket compressed
Zero deck ht

Figure .040" or close for gasket. You do n o t want an extra thick head gasket to make up for other design issues. Look up quench/head gaskets and you will understand why.

I haven't done the math (on phone on vacation) but with 93 octane, correct gasket and deck ht, and 22 dish pistons with those heads you should be ok but check!
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
You should be right around 9.6-1 with your combo i wouldnt worry about it aluminum heads can take a little more compression than iron heads and still run lower octane fuel. Of course a lot depends on deck height but still you should be fine
 
OP
OP
86Horn_EB_77

86Horn_EB_77

Jr. Member
Joined
Aug 31, 2006
Messages
100
Loc.
Austin
Thanks guys - I think it's the deck height that was stopping me from using the Summit calculator.

I probably didn't make it clear that I already have the stroker kit with the -4cc pistons - so I'm locked into those.

If I run the Summit CR tool with zero deck ht and a 0.040 head gasket using 60cc chambers - I end up with 11.55/1 CR - OUCH !!!

If I use some 64cc heads, I get 10.92 - still too high !

What am I missing - is there a better deck ht assumption to make? I'm guessing that I have to assemble the short block to measure it, right?

Thanks again
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
If I use some 64cc heads, I get 10.92 - still too high !

What am I missing - is there a better deck ht assumption to make? I'm guessing that I have to assemble the short block to measure it, right?

Thanks again

Are the pistons you have supposed to be zero deck height by design?..

In any event, yes, when you are shooting for a "zero-deck" setup, you have to assemble and measure. If you are going for extremely close quench tolerance, you had to have the decks squared and verify all 8 heights.
 

Outlaw Bronco

Full Member
Joined
Nov 27, 2011
Messages
153
Loc.
Shenandoah, VA
Check out Wallace Racing Calculators online and play around.

I get 10.2:1 CR with zero deck ht, 9.7:1 with the piston .020 in the hole.

I figure a flat top piston around 5.0cc's to account for the top ring land. Your typical FelPro head gasket is .041 thick with a 4.100 bore dia. As for the deck ht, your average is .020 in the hole, on a factory untouched block.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Here's a little chart I found for a stroker kit with -4 cc dish pistons. Dont know if these are the same but these pistons were made for TFS heads. While a tad bit higher than i would want to run I think it will still run fine. A lot also depends on what cam you use as a bigger cam may help bleed off some of the compression.
Part Number Cylinder Head Volume
58.0cc 61.0cc 64.0cc 68.0cc
14855-030 10.50 10.11 9.76 9.33
14855-040 10.54 10.15 9.80 9.37
14855-STD 10.38 10.00 9.65 9.22
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
You can also work the CR down with the right camshaft design, give the folks at Ford Stroker dot com a buzz.
 

Outlaw Bronco

Full Member
Joined
Nov 27, 2011
Messages
153
Loc.
Shenandoah, VA
Getting back to your original question, high port heads are only 1/2" raised, so unless your headers are binding up on object's now you shouldn't have any issues.
 
OP
OP
86Horn_EB_77

86Horn_EB_77

Jr. Member
Joined
Aug 31, 2006
Messages
100
Loc.
Austin
Wallace Racing Calculator

My stroker kit is the Coast Performance Pro street 4.030 bore with the -4cc flat top pistons (they do have valve reliefs cut into them - and should be good for cams up to .600 lift)

Using a 4.030 bore, 3.25 stroke, 60cc chamber, .041 head gasket, -4cc piston dish, 0.020 piston in the hole: CR = 9.85
With 0.010 in the hole, CR = 10.1

That's lower than the Summit CR calculator - I think I'm comfortable with about 10 to 1 - since I plan to run 93.

I'm planning on BC Shorty headers so I'm hoping that the extra 1/2" ht can be made up for the in the down pipes. Would be nice to use the BC 2 into 1 exhaust they sell to match the headers - but I'm guess that the high port heads might screw up the fit.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
Who's doing your balancing now that your header fit question is answered?
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Coasts website shows about 10.10 with 61CC heads.

You may want to double check the combustion chamber size of the high ports. I know they had several different combustion chamber sizes 58, 64, 67, and 70 cc. Also the exhuast ports are 3/4" taller than stock ports. still shouldnt be a issue considering that a 351W is 1in taller than a 302 and people swap them in all the time with little header issues.
 
OP
OP
86Horn_EB_77

86Horn_EB_77

Jr. Member
Joined
Aug 31, 2006
Messages
100
Loc.
Austin
Nvstuk - I bought this Coast stroker kit used in the box- and it was already balanced to 28oz by Coast. That's going to make me send my Exploder damper to Damper Dudes for a re-balance - but hey what's another $150 of Bronco funny money? The block/assy drive is a 96 Exploder 5.0.

The seller claims these high port heads are 60cc - although the only ones I can find at summit say 61cc - he might have milled them - I need to ask.

I will call the Ford Strokers dot com guys and ask about cams - looks like they make their own custom cams - and alot of it appears to be Mustang 1/4 mile stuff. I really want the opposite - good torque at less than 5000RPM (most area under the curve). I could care less about high RPM stuff.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
Ihax a custom roller can built by Ed @Flow induction.com. This is what Ed does for a living...its worth 50 bucks extra.... mine has instantaneous throttle response to 5500.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
Pm me...when I get home I'll explain why you want the balancing checked.
 
Top