• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Troubleshooting whistle / slight squeal

clinem03

Sr. Member
Joined
Sep 9, 2017
Messages
401
I have been replacing parts piece by piece after a lengthy restoration and slight engine rebuild. I drove the truck 50 miles or so yesterday, and on the last run I heard a 'whistle' when accelerating/rolling - when I come to a stop the whistle stops. But then I hear what sounds like a slight belt squeal at idle (again no whistle when stopped), and when I press the clutch pedal the slight squeal stops. I recently had my clutch and flywheel replaced and they also said they replaced the release bearing (which I thought was my issue given the friction in the clutch pedal when depressed and the slight squeal) when they replaced the clutch and flywheel so its new.

Does anyone have any ideas on what my issue could be?

Thanks in advance for the help. I love this forum and all the members who are so helpful in educating someone who is learning along the way!
 

Boss Hugg

Contributor
Bronco Guru
Joined
Jun 8, 2010
Messages
2,213
I don't think it's your whistle, but if you touch the clutch and a squeal stops, you need to adjust the rod just a tad to get it a touch more slack. If the throwout bearing is spinning while you're sitting still OFF the clutch, it's not gonna last anytime, and may already be done...

Address the belt squeal and you might find that to be your whistle while at speed.
 
OP
OP
clinem03

clinem03

Sr. Member
Joined
Sep 9, 2017
Messages
401
I don't think it's your whistle, but if you touch the clutch and a squeal stops, you need to adjust the rod just a tad to get it a touch more slack. If the throwout bearing is spinning while you're sitting still OFF the clutch, it's not gonna last anytime, and may already be done...

Address the belt squeal and you might find that to be your whistle while at speed.

Great advice, thank you!
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
does the noise come back when you rev the engine with the tranny in neutral and Bronco stopped?
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,781
Intake whistle. Noise the air makes running into carb or TB. We don't use air cleaners with all the baffles usually. Thats what/is mine is. Thought is was belt, pulleys, water pump bearing, everything. Then wife standing next to running motor says "hey, why is the intake whistling">
 
OP
OP
clinem03

clinem03

Sr. Member
Joined
Sep 9, 2017
Messages
401
does the noise come back when you rev the engine with the tranny in neutral and Bronco stopped?

Hard to tell with the exhaust. I did get her back on the road today for a little 30 min test run. No whistle during the entire ride. I also didn’t have any squeals during the ride until the last few miles. When sitting idle I would hear a repetitive squeal/squeak that would stop when I pressed the clutch pedal or even when I would just press it through its first few inches of travel, but not fully engage it. Thoughts? Should I adjust the rod? Could my throw out bearing be shot already?
 
OP
OP
clinem03

clinem03

Sr. Member
Joined
Sep 9, 2017
Messages
401
Intake whistle. Noise the air makes running into carb or TB. We don't use air cleaners with all the baffles usually. Thats what/is mine is. Thought is was belt, pulleys, water pump bearing, everything. Then wife standing next to running motor says "hey, why is the intake whistling">

That’s hilarious! You never think it’s the easy fix…
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
get out of the truck push the clutch peddle by hand. how much free peddle do you have to where the peddle push hits the throw out bearing before opening up the clutch?
 
OP
OP
clinem03

clinem03

Sr. Member
Joined
Sep 9, 2017
Messages
401
get out of the truck push the clutch peddle by hand. how much free peddle do you have to where the peddle push hits the throw out bearing before opening up the clutch?

About 2.5-3.5 inches (total estimate, was hard to tell)
 
Top