• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Vapor Cannister Hook up ??

wildhorses76

Full Member
Joined
Jul 17, 2007
Messages
243
Loc.
Kaplan, Louisiana
I bought a vapor cannister from SC74, I am trying to hook up all the factory vent stuff for the gas tank and vapor cannister and charcoal cannister so no fumes and no more gas pressurizing and spilling out of caps. There are four tubes coming from this cannister, I recently seen one with only three.

I currently have both the main and auxillary gas tank

Which line (hose) goes where on this cannister, or does it matter?

I also bought a round charcoal cannister to use under hood.....

FYI, there are no vent lines on the vehicle, PO stripped everything and had the tank plugged up with a short piece of hose and a screw in the end

Thanks for input!
 

Attachments

  • vapor cannister (Large).jpg
    vapor cannister (Large).jpg
    78.6 KB · Views: 113

csjr

Sr. Member
Joined
Apr 18, 2007
Messages
675
Loc.
Lighthouse Point, FL
I would venture to say that the four hose unit is for a duel tank setup. My truck originally came with duel tanks and had the four hose unit as well. A three hose unit must be for a one gas tank truck. My PO also pulled most of the stuff off, but there was a hard line--similar to fuel line and either 5/16 or 3/8, that ran from around the tank valve assembly, across the body support to the passenger side and then angled towards the front tire. I believe the stock charcoal cannister was mounted on the frame somewhere behind the starter area. If you have aftermarket exhaust you might have fitment issues there. Good luck with the setup and I'd love to see a pic or two when you have it hooked up. I think I threw all that stuff away when I took it off my rig. There may be a sketch of the setup in the Chilton's manual.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Of the 4 lines going into the condensation tank, 3 are for vapor (one for each gas tank vent, one for carbon canister) and should be plumbed to the top of the condensation tank. The other port on the condensation tank should go to the bottom of it to pickup liquid fuel which is routed back to the main tank. On the carbon canister there are 2 small ports, one for the cond. tank and one that goes to the air cleaner. Vapors get sucked into the engine and get burned.
 

Attachments

  • vapor rec.jpg
    vapor rec.jpg
    78.6 KB · Views: 142
OP
OP
wildhorses76

wildhorses76

Full Member
Joined
Jul 17, 2007
Messages
243
Loc.
Kaplan, Louisiana
Thanks! Will see if I can hook this stuff up and will take pics.....gotta get this cast off my ankle first though so may be a couple weeks.....just getting ready to dive in deep on this thing and get it on the road again......

Thanks ALL!!
 

MarsChariot

Contributor
Planetary Offroader
Joined
Oct 12, 2004
Messages
2,605
Loc.
Albuquerque, New Mexico
I bought a vapor cannister from SC74, I am trying to hook up all the factory vent stuff for the gas tank and vapor cannister and charcoal cannister so no fumes and no more gas pressurizing and spilling out of caps. There are four tubes coming from this cannister, I recently seen one with only three.

I currently have both the main and auxillary gas tank

Which line (hose) goes where on this cannister, or does it matter?

I also bought a round charcoal cannister to use under hood.....

FYI, there are no vent lines on the vehicle, PO stripped everything and had the tank plugged up with a short piece of hose and a screw in the end

Thanks for input!

Here is an annotated version of your image. The line to the charcoal is not sensitive to which line it connects to.
 

Attachments

  • vapor cannister (Large).jpg
    vapor cannister (Large).jpg
    139.4 KB · Views: 141

Baja71

Bronco Guru
Joined
Oct 16, 2004
Messages
2,908
Here is an annotated version of your image. The line to the charcoal is not sensitive to which line it connects to.

I carefully labeled mine when I pulled it, but why would any of the lines be sensitive to their connections? Is there something internal to the jug that makes it so? Especially when the lines are cut off like this one. Just curious.
 
OP
OP
wildhorses76

wildhorses76

Full Member
Joined
Jul 17, 2007
Messages
243
Loc.
Kaplan, Louisiana
After I got it I inspected it and seen that there are 3 internal tubes that go up in the cannister, one doesn't have a tube that extends inside making it the only one that will work for the liquid return back to the tank so any vapor that liquifies can drain properly. So the other 3 wouldn't be sensitive to what you hook them to. ....as far as i can tell....
 
Top